Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Manual Extrusion not working

    Scheduled Pinned Locked Moved Solved
    General Discussion
    4
    10
    128
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • wharris87undefined
      wharris87
      last edited by

      Hi All, trying to get my printer up and running after a long time of not using it.

      I never used to have a problem manually extruding, but it doesn't seem to work anymore.

      03/10/2024, 19:42:52 m115
      FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.3 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2021-06-15 21:45:03

      03/10/2024, 19:42:15 m122
      === Diagnostics ===
      RepRapFirmware for Duet 2 WiFi/Ethernet version 3.3 (2021-06-15 21:44:54) running on Duet WiFi 1.02 or later
      Board ID: 08DGM-917NK-F2MS4-7J1F8-3SD6N-KHT8F
      Used output buffers: 3 of 24 (12 max)
      === RTOS ===
      Static ram: 23876
      Dynamic ram: 75072 of which 80 recycled
      Never used RAM 15388, free system stack 164 words
      Tasks: NETWORK(ready,14.4%,237) HEAT(delaying,0.0%,314) Move(notifyWait,0.1%,364) MAIN(running,85.4%,441) IDLE(ready,0.1%,29), total 100.0%
      Owned mutexes: WiFi(NETWORK)
      === Platform ===
      Last reset 00:38:36 ago, cause: software
      Last software reset at 2024-10-03 19:03, reason: User, GCodes spinning, available RAM 15496, slot 0
      Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
      Error status: 0x00
      Step timer max interval 0
      MCU temperature: min 28.0, current 28.4, max 29.4
      Supply voltage: min 24.2, current 24.4, max 24.6, under voltage events: 0, over voltage events: 0, power good: yes
      Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
      Driver 0: position 0, standstill, SG min/max not available
      Driver 1: position 0, standstill, SG min/max not available
      Driver 2: position 0, standstill, SG min/max not available
      Driver 3: position 0, standstill, SG min/max not available
      Driver 4: position 0, standstill, SG min/max not available
      Driver 5: position 0
      Driver 6: position 0
      Driver 7: position 0
      Driver 8: position 0
      Driver 9: position 0
      Driver 10: position 0
      Driver 11: position 0
      Date/time: 2024-10-03 19:42:13
      Cache data hit count 4294967295
      Slowest loop: 12.37ms; fastest: 0.17ms
      I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
      === Storage ===
      Free file entries: 10
      SD card 0 detected, interface speed: 20.0MBytes/sec
      SD card longest read time 3.8ms, write time 0.0ms, max retries 0
      === Move ===
      DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
      === MainDDARing ===
      Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
      === AuxDDARing ===
      Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
      === Heat ===
      Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
      Heater 1 is on, I-accum = 0.0
      === GCodes ===
      Segments left: 0
      Movement lock held by null
      HTTP is idle in state(s) 0
      Telnet is idle in state(s) 0
      File is idle in state(s) 0
      USB is idle in state(s) 0
      Aux is idle in state(s) 0
      Trigger is idle in state(s) 0
      Queue is idle in state(s) 0
      LCD is idle in state(s) 0
      Daemon is idle in state(s) 0
      Autopause is idle in state(s) 0
      Code queue is empty.
      === Network ===
      Slowest loop: 15.75ms; fastest: 0.00ms
      Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
      HTTP sessions: 1 of 8

      • WiFi -
        Network state is active
        WiFi module is connected to access point
        Failed messages: pending 0, notready 0, noresp 0
        WiFi firmware version 1.23
        WiFi MAC address 84:0d:8e:b3:b4:98
        WiFi Vcc 3.40, reset reason Turned on by main processor
        WiFi flash size 4194304, free heap 24120
        WiFi IP address 192.168.0.2
        WiFi signal strength -68dBm, mode none, reconnections 0, sleep mode modem
        Clock register ffffffff
        Socket states: 0 0 0 0 0 0 0 0

      ; Configuration file for Duet WiFi (firmware version 3)
      ; executed by the firmware on start-up
      ;
      ; generated by RepRapFirmware Configuration Tool v3.1.4 on Sun Oct 18 2020 09:46:25 GMT+0100 (British Summer Time)

      ; General preferences
      G90 ; send absolute coordinates...
      M83 ; ...but relative extruder moves
      M550 P"BLV mgn Cube" ; set printer name
      M669 K1 ; select CoreXY mode

      ; Network
      M552 S1 ; enable network
      M586 P0 S1 ; enable HTTP
      M586 P1 S0 ; disable FTP
      M586 P2 S0 ; disable Telnet

      ; Drives
      M569 P0 S1 ; physical drive 0 goes forwards
      M569 P1 S1 ; physical drive 1 goes forwards
      M569 P2 S1 ; physical drive 2 goes forwards
      M569 P3 S0 ; physical drive 3 goes backwards
      M584 X0 Y1 Z2 E3 ; set drive mapping
      M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
      M92 X160.00 Y160.00 Z400.00 E418.00 ; set steps per mm
      M566 X720.00 Y720.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
      M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
      M201 X500.00 Y500.00 Z250.00 E1000.00 ; set accelerations (mm/s^2)
      M906 X1600 Y1600 Z1600 E1600 I30 ; set motor currents (mA) and motor idle factor in per cent
      M84 S30 ; Set idle timeout

      ; Axis Limits
      M208 X0 Y0 Z0 S1 ; set axis minima
      M208 X350 Y445 Z350 S0 ; set axis maxima

      ; Endstops
      M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
      M574 Y2 S1 P"ystop" ; configure active-high endstop for high end on Y via pin ystop
      M574 Z1 S2 ; configure Z-probe endstop for low end on Z

      ; Z-Probe
      M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
      M558 P9 C"^zprobe.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
      G31 P25 X28.5 Y-5 Z0 ; set Z probe trigger value, offset and trigger height
      M557 X15:285 Y15:285 S20 ; define mesh grid

      ; Heaters
      M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
      M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
      M307 H0 B0 R0.811 C653.0 D4.65 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
      M140 H0 ; map heated bed to heater 0
      M143 H0 S100 ; set temperature limit for heater 0 to 100C
      M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
      M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
      M307 H1 B0 R5.298 C98.0:67.3 D3.29 S1.00 ; disable bang-bang mode for heater and set PWM limit

      ; Fans
      M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
      M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
      M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
      M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
      M950 F2 C"fan1" Q500 ; create fan 2 on pin fan1 and set its frequency
      M106 P2 S1 H1 T45 ; set fan 2 value. Thermostatic control is turned on

      ; Tools
      M563 P0 D0 H1 F0 ; define tool 0
      G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
      G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

      ; Custom settings are not defined

      ; Miscellaneous
      M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

      I am at a loss!

      M563 P0 D0 H1 F0 seems to be right?
      M302 states that cold extrusion is prohibited, but as per attached, T0 temp is well above the 160 degC minimum, but the manual extrusion buttons are greyed out.

      What am i missing?

      Many thanks in advancesnip 1.PNG snip 2.PNG

      infiniteloopundefined 1 Reply Last reply Reply Quote 0
      • infiniteloopundefined
        infiniteloop @wharris87
        last edited by

        @wharris87 said in Manual Extrusion not working:

        What am i missing?

        A T0 at the end of your config.

        wharris87undefined 1 Reply Last reply Reply Quote 0
        • wharris87undefined
          wharris87 @infiniteloop
          last edited by

          @infiniteloop

          Where do i need to type it?

          infiniteloopundefined dc42undefined 2 Replies Last reply Reply Quote 0
          • infiniteloopundefined
            infiniteloop @wharris87
            last edited by infiniteloop

            @wharris87

            where …

            As I wrote: at the end of your config. Place it above or below the 'Miscellaneous' section.

            wharris87undefined 1 Reply Last reply Reply Quote 0
            • dc42undefined
              dc42 administrators @wharris87
              last edited by

              @wharris87 you need to have a tool selected in order to extrude. If you have just one tool then it's common to select it at the end of config.g.

              Duet WiFi hardware designer and firmware engineer
              Please do not ask me for Duet support via PM or email, use the forum
              http://www.escher3d.com, https://miscsolutions.wordpress.com

              infiniteloopundefined 1 Reply Last reply Reply Quote 0
              • wharris87undefined
                wharris87 @infiniteloop
                last edited by

                @infiniteloop

                Ah, that simple! Thanks, will give it a try

                1 Reply Last reply Reply Quote 0
                • infiniteloopundefined
                  infiniteloop @dc42
                  last edited by

                  @dc42 said in Manual Extrusion not working:

                  you need to have a tool selected in order to extrude.

                  Looking at the config.g of @wharris87, that's the obvious cause. However, on the DWC screenshot, the tool "Heater 1" is active and at temperature, but the extrusion controls are dimmed nonetheless. So possibly, something else is going wrong. Maybe some unlucky mismatch of DWC and RRF versions? For personal reasons, I am not that familiar with RRF 3.1.4 (specified version of the configuration tool) to 3.3 (from the M115 report) - can you recall any issues related to that?

                  droftartsundefined 1 Reply Last reply Reply Quote 0
                  • droftartsundefined
                    droftarts administrators @infiniteloop
                    last edited by droftarts

                    @wharris87 @infiniteloop The heater may be active, but the tool isn't. The tool is highlighted when it is active. Subtle difference, I know. See https://docs.duet3d.com/en/User_manual/Reference/Duet_Web_Control_Manual#selecting-a-tool
                    alt text

                    Ian

                    Cartesian bed-slinger with Duet 3 Mini 5+ WiFi and 1LC : RRP Fisher Delta v1 with Duet 2 Maestro : TronXY X5S with Duet 3 MB6HC and Roto toolboard

                    infiniteloopundefined 1 Reply Last reply Reply Quote 1
                    • infiniteloopundefined
                      infiniteloop @droftarts
                      last edited by

                      @droftarts Thanks for your correction - subtle as always 😳

                      wharris87undefined 1 Reply Last reply Reply Quote 0
                      • wharris87undefined
                        wharris87 @infiniteloop
                        last edited by

                        @infiniteloop Adding T0 in did the trick.

                        Many thanks for the swift support and guidance!

                        1 Reply Last reply Reply Quote 0
                        • dc42undefined dc42 marked this topic as a question
                        • dc42undefined dc42 has marked this topic as solved
                        • First post
                          Last post
                        Unless otherwise noted, all forum content is licensed under CC-BY-SA