Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Bed Leveling Daedalus/Railcore Printer -from Project R3D

    Scheduled Pinned Locked Moved
    Tuning and tweaking
    2
    4
    44
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • sportdocundefined
      sportdoc
      last edited by

      I'm trying to sort out issues leveling the best on a daedalus 3d printer from Project R3d. From what I can tell it is mostly a RTP Railcore. It is a printer I inherited at work. It runs on a Duet3 board. Post is short because longer was not allowed by the forum.

      1 Reply Last reply Reply Quote 1
      • sportdocundefined
        sportdoc
        last edited by

        The current heightmap shows a range from -2.989 to +2.080 mm. I've moved the print nozzle to the 4 corners as a test, and the deviation I find is only about 0.3 to 0.4 mm. I have ran G32 multiple times and the results never really get better, just different.

        1 Reply Last reply Reply Quote 1
        • Phaedruxundefined
          Phaedrux Moderator
          last edited by

          Can you post an image of your heightmap and the bed.g and config.g files so we can see what it's actually doing?

          Z-Bot CoreXY Build | Thingiverse Profile

          sportdocundefined 1 Reply Last reply Reply Quote 0
          • sportdocundefined
            sportdoc @Phaedrux
            last edited by

            @Phaedrux
            This unit came with a Ez-abl inductive bed sensor. Originally it was probing the bed on a 9 point grid. I changed that to 16 in hopes that it would be better. I was trying to avoid the magnets a bit more. This 16 point grid is what is currently active, but the 9 point grid is commented out in config.g.

            Here is a screen shot of the bed level - heightmap302925.jpg
            The front left is 2.080, the rear right is -2.989

            Comment: I manually moved the bed to check height at all 4 corners. The difference was about 0.3 to 0.5mm, not 5 mm. Regardless of how many times I run the G32, the values virtually never changes.

            Here is the config.g

            G21 ;Work in millimetres
            G90 ;Send absolute coordinates...
            M83 ;...but relative extruder moves

            ; Axis and motor configuration
            M569 P0 S1 ;Drive 0 X / Rear
            M569 P1 S1 ;Drive 1 Y / Front
            M569 P2 S1 ;Drive 2 Z Front Left
            M569 P3 S1 ;Drive 3 Z Rear Left
            M569 P4 S1 ;Drive 4 Z Right
            M569 P5 S0 ;Drive 5 Extruder
            M667 S1 ;corexy mode

            M584 X0 Y1 Z2:3:4 E5 ; Map X to drive 0 Y to drive 1, Z to drives 2, 3, 4, and E to drive 5
            ;Leadscrew locations
            ;M671 X-38:-38:340 Y62.5:247.5:139 S7.5 ;X -38, -38, 340
            ;Leadscrew locations
            ;M671 X-24:-24:325 Y32:287:159 S7.5 ;X -38, -38, 340 this was the setting on 3/28/25
            M671 X-34:-34:344 Y50:206:167 S7.5 ;X --34, -34, 344 Y 50, 206, 167 as measured on 3/28/25

            M350 X16 Y16 Z16 E16 I1 ;set 16x microstepping for axes with interpolation
            M906 X1600 Y1600 Z1200 E600 I60 ;Set motor currents (mA) reduced E to 600 for lgx extruder
            M201 X2000 Y2000 Z100 E1500 ;Accelerations (mm/s^2)
            M203 X24000 Y24000 Z900 E3600 ;Maximum speeds (mm/min) was Z1800 tr8*4
            M566 X1000 Y1000 Z100 E1500 ;Maximum jerk speeds mm/minute E60 Z60
            M208 X310 Y300 Z345 ;set axis maxima and high homing switch positions (adjust to suit your machine)
            M208 X0 Y0 Z-0.9 S1 ;set axis minima and low homing switch positions (adjust to make X=0 and Y=0 the edges of the bed)
            M92 X200 Y200 Z1600 E400 ;steps/mm 0.9 z

            ; End Stops
            M574 X1 S1 P"io3.in" ;Map the X endstop to io3.in
            M574 Y2 S1 P"io1.in" ;May the Y endstop to io1.in

            ; Filament Sentinel
            M591 P1 C"io4.in" S0 D0 ; filament monitor connected to E0 endstop

            ; Thermistors
            M308 S0 P"temp0" Y"thermistor" A"bed_heat" T100000 B4240 H0 L0 ;Bed thermistor - duet 3, connected to temp0

            M308 S1 P"temp1" Y"thermistor" A"e0_heat" T100000 B4725 C7.06e-8 H0 L0 ;duet3 e3d

            ;Define Heaters
            M950 H0 C"out0" T0 ;Bed heater is on out0
            M950 H1 C"out1" T1 ;Hotend heater is on out1

            M307 H0 A154.6 C1043.8 D1.5 S1.00 B1 ;Bed Heater duet 3 configuration
            M307 H1 A370.6 C134.5 D4.1 S1.00 B0 ;Hotend duet 3 configuration 2/22/25 PID tune date

            M570 S360 ;Hot end may be a little slow to heat up so allow it 180 seconds
            M143 S305 ;Set max hotend temperature

            ; Fans
            M950 F0 C"out4" ;Hotend fan on "out4" connector
            M106 P0 S255 H1 T0 ;enable thermostatic mode for hotend fan
            M950 F1 C"out5" ;Layer fan on "out5" connector
            M106 P1 S0 ;Layer Fan
            M950 F2 C"out6" ;Layer fan on "out6" connector
            M106 P2 S0 ;Layer Fan

            ; Tool definitions
            M563 P0 D0 H1 F1:2 ;Define tool 0
            G10 P0 S0 R0 ;Set tool 0 operating and standby temperatures

            ;EZ ABL
            M558 P5 C"!io7.in" I1 H10 F180 T3600 ; set Z probe type to EZ ABL and the dive height + speeds
            ; from th3d M558 P5 C"!io7.in" H3 F900 T12000
            G31 X-9.25 Y63 Z1.75 P25 ;Z offset can be adjusted here

            M575 P1 S1 B57600

            ;G29 S1

            ; M557 X30:280 Y66:300 S125:117 ; This was the stock settings on the machine 3/29/25
            M557 X15:300 Y66:300 S95:117 ;Trial setting 3/28/25

            M501
            M140 H0
            T0 ;select first hot end

            1 Reply Last reply Reply Quote 0
            • First post
              Last post
            Unless otherwise noted, all forum content is licensed under CC-BY-SA