Weird G32/G29 Error
-
So it was working correctly with firmware 1.21 before? If so then it looks like the changes to the config files caused the problem.
-
No the error started at FW 1.21 and i did an upgrade to exclude an FW error. also G30, Homez and homeall did work but G32 and G29 doesnt do whats in bed.g or in M557
-
What did you do that triggered the error: a firmware upgrade from a version earlier than 1.21, or something else?
-
I run the FW 1.21 a couple of weeks, two weeks ago i changed from IR Probe to Orion. I first thought i made a mistake at my config.g yesterday, so i build a new one today. As this didn`t worked i made the FW Update to exclude an Firmware Issue.
Then i thought something on the Board is broken but G30, homeall and homez worked as they should.
Dont shure if this also is a part of the problem, but my last 3 Thermistor and Thermistor Cables made Heater Faults if the cable is moved in the wrong way...
-
Tried it again, Setup Firmware again, Homeall works like a charm. Start G32, first start point should is defined in bed.g as X40 Y40 but he tried to move to X-90 Y-90? What am i doing wrong?
-
Do you have any deployprobe.g. or retractprobe.g files that shouldn't be there?
-
@dc42 No, even after the new Installation of the Firmware isn't there a deployprobe.g or an retractprobe.g
-
Please share your config.g and bed.g files.
-
config.g
; Configuration file for Duet WiFi (firmware version 1.20 or newer)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Sat Jun 30 2018 19:52:00 GMT+0200; General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
M555 P1 ; Set firmware compatibility to look like RepRapFirmareM667 S1 ; Select CoreXY mode
; Network
M550 PHEVO ; Set machine name
M552 S1 ; Enable network
;*** Access point is configured manually via M587
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet; Drives
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S0 ; Drive 2 goes backwards
M569 P3 S1 ; Drive 3 goes forwards
M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
M92 X80 Y80 Z800 E2673 ; Set steps per mm
M566 X1000 Y1000 Z1000 E240 ; Set maximum instantaneous speed changes (mm/min)
M203 X12000 Y12000 Z250 E40 ; Set maximum speeds (mm/min)
M201 X800 Y800 Z250 E1000 ; Set accelerations (mm/s^2)
M906 X800 Y800 Z800 E500 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X280 Y280 Z250 S0 ; Set axis maxima; Endstops
M574 X1 Y1 S1 ; Set active high endstops; Z-Probe
M574 Z1 S2 ; Set endstops controlled by probe
M558 P8 I1 R0.4 Z1 F300 ; Set Z probe type to unmodulated and the dive height + speeds
G31 P500 X140 Y140 Z-0.1 ; Set Z probe trigger value, offset and trigger height
M557 X20:280 Y20:280 S20 ; Define mesh grid; Heaters
M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S280 ; Set temperature limit for heater 1 to 280C
M307 H1 A469.9 C164.2 D9.6 B0; Fans
M106 P0 S1 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H-1 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P2 S1 I0 F500 H1 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on; Tools
M563 P0 D0 H1 F1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C; Automatic saving after power loss is not enabled
; Custom settings are not configured
M106 P1 S0
M572 D0 S0.08 ;Pressure Advancebed.g
; bed.g
; called to perform automatic bed compensation via G32
;
; generated by RepRapFirmware Configuration Tool on Sat Jun 30 2018 19:52:00 GMT+0200
M561 ; clear any bed transform
; Probe the bed at 4 points
G30 P0 X40 Y40 H0 Z-99999
G30 P1 X40 Y140 H0 Z-99999
G30 P2 X40 Y270 H0 Z-99999
G30 P3 X140 Y270 H0 Z-99999
G30 P4 X270 Y270 H0 Z-99999
G30 P5 X270 Y140 H0 Z-99999
G30 P6 X270 Y40 H0 Z-99999 S0 -
In your G31 command you have specified that the Z probe is offset from the nozzle by 140mm (which is a very large offset) in both X and Y. So in order to put the probe at 40,40 the firmware has to put the nozzle at -100,-100.
-
facepalm feels like an idiot, doesn`t see that. Redefine the offset in G31 and everythings fine now. Thanks!
