Ideas for more realistic bed temperature control
-
I have a bed consisting of a Thermal blanket, MK2 heatbed, 4mm alu plate, brosilicate glass plate 3mm. I drilled a hole in the alu plate and have the thermistor touching the glass plate.
This works very well!
I am thinking about filling the hole up with high temp silicon gel when the thermistor is there.
In your case I would drill a 5mm deep hole in the alu put a spare thermistor there and fill it with heat resistant silicon. No idea if that would work of course.
-
@nemesis said in Ideas for more realistic bed temperature control:
In your case I would drill a 5mm deep hole in the alu put a spare thermistor there and fill it with heat resistant silicon. No idea if that would work of course.
Forgot to mention that the heater is a glued-on silicone mat - I'm not sure whether I could easily remove it from the aluminium plate, and I'd rather not drill into a mains-connected heater, neither on purpose nor accidentally. The end of the year is night, but these are not the kind of fireworks I'm looking for...
-
@vwegert I have a very similar setup on my new delta build. Stuck at work on the last day waiting for the BuildTak FlexPlate system to be delivered. The last part of my build.
I did some initial tests with mine and found that because of the large thermal mass, heating the bed and then giving it time to equalise actually gave nice consistent temperatures. Yes it means having the bed on for a while before starting the print but having the large thermal mass means it takes less effort to keep at temperature once achieved.
Another option would be to cut a small channel on the top of your Aluminium plate running to the centre. Run your thermistor along that then stick the magnetic sheet on top of that.
Richard
-
@richardmckenna said in Ideas for more realistic bed temperature control:
Another option would be to cut a small channel on the top of your Aluminium plate running to the centre. Run your thermistor along that then stick the magnetic sheet on top of that.
I don't have the tools to do that properly, I'm afraid... I'll try the "moar patient moar better" approach, but it's hard
-
@vwegert ha ha I hate waiting too. Waiting for this parcel is driving me crazy.
I'll do some more tests when I have it installed and let you know how it goes.
-
@vwegert said in Ideas for more realistic bed temperature control:
Forgot to mention that the heater is a glued-on silicone mat - I'm not sure whether I could easily remove it from the aluminium plate, and I'd rather not drill into a mains-connected heater, neither on purpose nor accidentally. The end of the year is night, but these are not the kind of fireworks I'm looking for...
Ah no. Please do not drill through the heater
With a 6mm alu bed you could in theory purchase a long 4mm drill (https://uk.rs-online.com/web/p/twist-drill-bits/5226651/), drill from the side and stop in the middle. However do not attempt this without the proper tools and patience!
-
With 6mm aluminium, the temperature should be fairly uniform across the bed except at the edges. So no need to drill as far as the middle.
Duet WiFi hardware designer and firmware engineer
Please do not ask me for Duet support via PM or email, use the forum
http://www.escher3d.com, https://miscsolutions.wordpress.com -
in that case a normal 4 mm drill would do. Just make sure you drill it straight! You do want to drill into your heater by accident.
-
@dc42 Now I wish I had a FLIR to see how uniform the temperature really is on the surface and how far in I would have to go to get a realistic measurement... A shame that these things are so expensive...
-
@nemesis said in Ideas for more realistic bed temperature control:
You do want to drill into your heater by accident.
No I don't.
-
@vwegert said in Ideas for more realistic bed temperature control:
@dc42 Now I wish I had a FLIR to see how uniform the temperature really is on the surface and how far in I would have to go to get a realistic measurement... A shame that these things are so expensive...
I looked into buying one of those and from I have been able to deduce the precision of a FLIR is not that good. A spot measuring tool is much cheaper and far more precise. Do that's what I use now. It takes a lot more time to measure the whole bed though...
