Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Creality Ender 5 Configuration

    Scheduled Pinned Locked Moved Solved
    Firmware installation
    12
    23
    6.4k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Brian_Kundefined
      Brian_K
      last edited by

      Would anyone have, or be able to point me towards, a configuration file for an Ender 5. I am looking to fit a BL Touch and an E3D V6 hotend, but I can figure those out from the standard machine.

      Thanks

      1 Reply Last reply Reply Quote 2
      • Vetiundefined
        Veti
        last edited by

        there isnt one. creality hasnt even released there marlin firmware.

        i suggest you start of with an ender 3 config as it should be close.

        1 Reply Last reply Reply Quote 1
        • Brian_Kundefined
          Brian_K
          last edited by

          Thanks, that's what I figured. Should i go with the Ender 3 settings but set as a CoreXY printer?

          1 Reply Last reply Reply Quote 0
          • mindofteaundefined
            mindoftea
            last edited by

            Hey, I'm in the same boat! I'll be configuring for an Ender 5 as soon as I get my new Maestro board talking to me again.

            I think the kinematics of the Ender 5 are actually Cartesian, rather than CoreXY, since the Y stepper just moves the X gantry back and forth.

            1 Reply Last reply Reply Quote 2
            • Brian_Kundefined
              Brian_K
              last edited by

              Thanks, wasn't sure, I'll work on that basis and just put the Z drive into reverse.

              1 Reply Last reply Reply Quote 0
              • Phaedruxundefined
                Phaedrux Moderator
                last edited by

                Ender 5 is cartesian, not corexy.

                This may help guide you a bit on what info you'll need for the configurator.

                https://duet3d.dozuki.com/Wiki/Going_from_Marlin_on_Arduino_to_RepRapFirmware_on_Duet

                Z-Bot CoreXY Build | Thingiverse Profile

                1 Reply Last reply Reply Quote 0
                • Modtcassundefined
                  Modtcass
                  last edited by

                  I have my the Duet Wifi CR-10S setup with EZABL and Titan Aero, I can share my configs with you if that will help you get things going. You'll have to adjust your steps and figure out the proper config for your probe.

                  1 Reply Last reply Reply Quote 1
                  • Brian_Kundefined
                    Brian_K
                    last edited by

                    Cracked it!!

                    Well, lots of tuning to do but fans working, heaters working, print head and bed moving around as smooth as can be. And quite, did I mention quite, whhhhisper quiet!!!

                    I can go to bed now it’s only 05:00am

                    Before I go, have a look at this guy on Youtube, his video was of immense help.

                    https://www.youtube.com/watch?v=6nqddfxHla0

                    Well done Duet, a great product.

                    1 Reply Last reply Reply Quote 1
                    • mindofteaundefined
                      mindoftea
                      last edited by

                      Sounds like we both got good configs! Here's mine for comparison: https://gist.github.com/mindoftea/c0dc708a8f63b4652e3d460ea56e2824

                      1 Reply Last reply Reply Quote 2
                      • XTLundefined
                        XTL
                        last edited by

                        I'm also waiting for a Duet wifi for my Ender 5. Having others' configurations will be good if I want to check something. Thank you.

                        I might mention an issue I've also been bouncing around a bit. It seems that my Ender 5 had overlong screws that attach the power supply. One had broken through the insulation under +V and shorted it to the chassis. Since the DC side (and possibly AC side for that matter) is floating, it didn't smoke anything, but it did cause parts such as the SD card slot to be at -24 V potential from the chassis. You might want to check yours.

                        I'm also curious about how people mounted the boards.

                        3dmntbighkerundefined 1 Reply Last reply Reply Quote 0
                        • 3dmntbighkerundefined
                          3dmntbighker @XTL
                          last edited by

                          @xtl said in Creality Ender 5 Configuration:

                          I might mention an issue I've also been bouncing around a bit. It seems that my Ender 5 had overlong screws that attach the power supply. One had broken through the insulation under +V and shorted it to the chassis. Since the DC side (and possibly AC side for that matter) is floating, it didn't smoke anything, but it did cause parts such as the SD card slot to be at -24 V potential from the chassis. You might want to check yours.

                          My Ender 3 Pro came with some PSU screws that seemed way too long for my comfort as well. I used a nut as a spacer at the time I assembled it just to be safe. If I recall it came assembled, and the only reason I noticed was that I took it apart to inspect something.

                          Scratch built CoreXY with Maestro
                          Heavily modified Ender 3 with Maestro
                          MPCNC work in progress with Duet WiFi

                          1 Reply Last reply Reply Quote 0
                          • XTLundefined
                            XTL
                            last edited by

                            I took the PSU apart as a replacement should be on its way. Turns out another screw reached in far enough to leave a round indent in the insulation and the solder trace underneath. The trace between the mains rectifier (or its NTC) and the main reservoir cap positive. That probably had just barely not broken through.

                            OTOH, I picked up my Duet Wifi board from mail this morning, so there's some exciting work ahead.

                            1 Reply Last reply Reply Quote 0
                            • codiac2600undefined
                              codiac2600
                              last edited by

                              I'm working on this exact mod right now. Thanks for sharing the config. I should be up and ready to test some time tonight just have to terminate EVERY connector correctly so I can plug it in to test.

                              1 Reply Last reply Reply Quote 0
                              • fundixundefined
                                fundix
                                last edited by

                                Hi, I am wiring Duet Mastro to my Ender 5. I created reduction for main box screws. I will try mover power supply and get duet to the original enclosure.

                                1 Reply Last reply Reply Quote 0
                                • XTLundefined
                                  XTL
                                  last edited by XTL

                                  I finally got everything back together and have enough configuration that homing, heating, cooling and all the other connections seem to be working.
                                  Now I'll need to get on with calibrations and settings hunts and tests, but I'm hoping to have the printer back in running condition soon.

                                  0_1556391889675_20190427_194319.jpg

                                  It is very cramped, but it's in there now. After this, I decided to flip the bottom cover so the fan is outside and drilled a hole for the fan wires. I'll need to print or otherwise make some blanking plates and plugs for the extra holes.

                                  MrHtgreenundefined 1 Reply Last reply Reply Quote 0
                                  • MrHtgreenundefined
                                    MrHtgreen @XTL
                                    last edited by

                                    @xtl Hello. Glad you got everything working. Any chance you could send your confing as im kind of stuck. Thank you in advance.

                                    Phaedruxundefined 1 Reply Last reply Reply Quote 0
                                    • XTLundefined
                                      XTL
                                      last edited by

                                      I don't have much of a config yet. I might have managed to calibrate the extruder (E378.66) and fought with my network devices all day today. Maybe someone will have good answers if you can describe what the exact problem is.

                                      1 Reply Last reply Reply Quote 0
                                      • Phaedruxundefined
                                        Phaedrux Moderator @MrHtgreen
                                        last edited by

                                        @mrhtgreen The Ender 3 Pro is pretty close to the Ender 5, if you need a look at an example config to get you unstuck perhaps this will help: https://forum.duet3d.com/topic/10196/ender-3-pro-configuration/11

                                        What specifically are you stuck on? What works and doesn't work?

                                        Z-Bot CoreXY Build | Thingiverse Profile

                                        1 Reply Last reply Reply Quote 1
                                        • Brian_Kundefined
                                          Brian_K
                                          last edited by Brian_K

                                          This is working pretty well on my Ender 5, still playing with the settings but had some nice prints from it.

                                          Points to note, I am using a geared extruder and a none Creality stepper motor on the X carriage. If you load the .json file into RR configurator, make changes to suit your setup you should at least be up and running.

                                          https://drive.google.com/open?id=1b1Gn-cnLB-sOeeHe4wOwwzi_YWfRM7oO
                                          [0_1557268102482_config.zip](Uploading 100%)

                                          1 Reply Last reply Reply Quote 2
                                          • Brian_Kundefined
                                            Brian_K
                                            last edited by

                                            A little bit of ringing (think that's what they call it) to take care of, but overall very happy.

                                            0_1557351439646_Hero Me.jpg

                                            1 Reply Last reply Reply Quote 1
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA