Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Duet Maestro BLV AM8 upgrade

    Scheduled Pinned Locked Moved
    General Discussion
    3
    5
    196
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • lichundefined
      lich
      last edited by

      Hi Hoping some one can help ,I have been through the forum read all the post and tried all the fixe's .
      Fitted a Maestro to an anet a8 that has had an BLV AM8 upgrade.
      The x carriage and Y carriage will not move ,The Z carriage makes a horrible clicking sound when it moves .
      Home X the Z carriage moves home Y the Z carriage moves, It will not see the endstops .
      The extruder will not Move .
      The only thing left from the anet is four stepper motors and two endstops.
      The Duet has been upgraded to 3.01
      Her is a copy of my config file
      ; General preferences
      G90 ; send absolute coordinates...
      M83 ; ...but relative extruder moves
      M550 P"Lich3D" ; set printer name
      M918 P1 E4 F2000000 ; configure direct-connect display

      ; Network
      M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP
      M586 P0 S1 ; enable HTTP
      M586 P1 S0 ; disable FTP
      M586 P2 S0 ; disable Telnet

      ; Drives
      M569 P0 S1 ; physical drive 0 goes forwards
      M569 P1 S1 ; physical drive 1 goes forwards
      M569 P2 S0 ; physical drive 2 goes backwards
      M569 P3 S1 ; physical drive 3 goes forwards
      M584 X0 Y1 Z2 E3 ; set drive mapping
      M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
      M92 X100.00 Y100.00 Z400.00 E873.08 ; set steps per mm
      M566 X600.00 Y600.00 Z18.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
      M203 X6000.00 Y6000.00 Z180.00 E6000.00 ; set maximum speeds (mm/min)
      M201 X1500.00 Y1500.00 Z100.00 E10000.00 ; set accelerations (mm/s^2)
      M906 X500 Y500 Z500 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
      M84 S30 ; Set idle timeout

      ; Axis Limits
      M208 X-33 Y-10 Z0 S1 ; set axis minima
      M208 X220 Y220 Z240 S0 ; set axis maxima

      ; Endstops
      M574 X1 S0 P"xstop" ; configure active-low endstop for low end on X via pin xstop
      M574 Y1 S0 P"ystop" ; configure active-low endstop for low end on Y via pin ystop

      ; Z-Probe
      M950 S0 C"zprobe.mod." ; create servo pin 0 for BLTouch
      M558 P9 C"^zprobe.in" H5 F100 T6000 ; set Z probe type to bltouch and the dive height + speeds
      G31 X20 Y0 Z3.3 P25 ; Z probe trigger value, offset in relation to nozzle. And trigger height adjustment
      M557 X20:200 Y20:200 S40 ; define mesh grid

      ; Heaters
      M308 S0 P"bedtemp" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 0 as thermistor on pin bedtemp
      M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
      M143 H0 S130 ; set temperature limit for heater 0 to 130C
      M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
      M140 H0 ; map heated bed to heater 0
      M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin e0temp
      M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
      M143 H1 S275 ; set temperature limit for heater 1 to 275C
      M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit

      ; Fans
      M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
      M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
      M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
      M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on

      ; Tools
      M563 P0 D0 H1 F0 ; define tool 0
      G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
      G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

      ; Custom settings are not defined

      ; Miscellaneous
      T0 ; select first tool

      Any guidance would been helpful

      PaulHewundefined dc42undefined 2 Replies Last reply Reply Quote 0
      • PaulHewundefined
        PaulHew @lich
        last edited by

        @lich Do the endstops register in DWC, on the 'Machine-Specific' page when you manually trigger them?
        Please post a picture of your endstop wiring, board side and check that you used the outer pins in the 3 pin connector.

        If Z is moving when homing X, could point to a possible wiring issue or wrong socket, maybe.

        P.

        RailCore II - Duet Mini + 1LC, Voron V0.1 - Duet Mini
        Voron 2.4 disassembled..... Waiting for the RailCore Mini....

        1 Reply Last reply Reply Quote 0
        • lichundefined
          lich
          last edited by

          The endstops do not register in dwc when triggerd I have wired them to the outer pins on the board,
          I have check the wiring to the X Y Z axis all in the right sockets ,the wiring to the duet maestro is as the diagram states

          1 Reply Last reply Reply Quote 0
          • dc42undefined
            dc42 administrators @lich
            last edited by

            @lich said in Duet Maestro BLV AM8 upgrade:

            ; Endstops
            M574 X1 S0 P"xstop" ; configure active-low endstop for low end on X via pin xstop
            M574 Y1 S0 P"ystop" ; configure active-low endstop for low end on Y via pin ystop

            You appear to be using normally-open endstop switches and RRF 3.x. Change those lines to:

            M574 X1 S1 P"!xstop" ; configure active-low endstop for low end on X via pin xstop
            M574 Y1 S1 P"!ystop" ; configure active-low endstop for low end on Y via pin ystop

            Duet WiFi hardware designer and firmware engineer
            Please do not ask me for Duet support via PM or email, use the forum
            http://www.escher3d.com, https://miscsolutions.wordpress.com

            lichundefined 1 Reply Last reply Reply Quote 0
            • lichundefined
              lich @dc42
              last edited by

              @dc42 said in Duet Maestro BLV AM8 upgrade:

              @lich said in Duet Maestro BLV AM8 upgrade:

              ; Endstops
              M574 X1 S0 P"xstop" ; configure active-low endstop for low end on X via pin xstop
              M574 Y1 S0 P"ystop" ; configure active-low endstop for low end on Y via pin ystop

              You appear to be using normally-open endstop switches and RRF 3.x. Change those lines to:

              M574 X1 S1 P"!xstop" ; configure active-low endstop for low end on X via pin xstop
              M574 Y1 S1 P"!ystop" ; configure active-low endstop for low end on Y via pin ystop

              Thank you dc42 that has got the endstops working

              1 Reply Last reply Reply Quote 0
              • First post
                Last post
              Unless otherwise noted, all forum content is licensed under CC-BY-SA