• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

IR Sensor and trigger hight

Scheduled Pinned Locked Moved
IR Height Sensor
3
16
575
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    observatoer
    last edited by 24 May 2020, 16:55

    Bed surface is a Geckotech.

    ; Z-Probe
    M558 P8 C"io3.in" H5 F120 T6000
    G31 P500 X-2 Y26.42 Z3.14

    1 Reply Last reply Reply Quote 0
    • undefined
      Phaedrux Moderator
      last edited by 24 May 2020, 16:59

      @observatoer said in IR Sensor and trigger hight:

      M558 P8

      You should be using M558 P1 for analogue probe mode.

      Z-Bot CoreXY Build | Thingiverse Profile

      undefined 1 Reply Last reply 24 May 2020, 17:01 Reply Quote 0
      • undefined
        observatoer @Phaedrux
        last edited by 24 May 2020, 17:01

        @Phaedrux Tried P1 w same result. Saw a comment from DC42 to use Mode 8 for the probe on RRF3.

        1 Reply Last reply Reply Quote 0
        • undefined
          Phaedrux Moderator
          last edited by 24 May 2020, 17:04

          Does performance change with a piece of paper on the bed surface?

          Z-Bot CoreXY Build | Thingiverse Profile

          undefined 1 Reply Last reply 24 May 2020, 17:05 Reply Quote 0
          • undefined
            observatoer @Phaedrux
            last edited by 24 May 2020, 17:05

            @Phaedrux No, I already tried different surfaces and they where detected equally.

            1 Reply Last reply Reply Quote 0
            • undefined
              Phaedrux Moderator
              last edited by 24 May 2020, 17:07

              so you've gone through this procedure?

              https://duet3d.dozuki.com/Wiki/Test_and_calibrate_the_Z_probe

              Z-Bot CoreXY Build | Thingiverse Profile

              undefined 1 Reply Last reply 24 May 2020, 17:08 Reply Quote 0
              • undefined
                observatoer @Phaedrux
                last edited by 24 May 2020, 17:08

                @Phaedrux Yes, several times to confirm doing it right.

                1 Reply Last reply Reply Quote 0
                • undefined
                  Phaedrux Moderator
                  last edited by 24 May 2020, 17:11

                  So what exactly is happening incorrectly? I'm not sure I understand from your first post.

                  When you use G30 s-1 to measure the trigger height, what value do you get?
                  When you use that value in G31 Z, are you able to move the nozzle to touch the bed at z0?

                  Z-Bot CoreXY Build | Thingiverse Profile

                  undefined 1 Reply Last reply 24 May 2020, 17:16 Reply Quote 0
                  • undefined
                    observatoer @Phaedrux
                    last edited by 24 May 2020, 17:16

                    @Phaedrux
                    Doing G30 S-1 gives me 3.14. Adding this to the config.g and home Z gives me Z=0, but the nozzle is esteem. 3.14mm above the bed.
                    If I reajust the probe hight, the same thing happens, just with different values. Higher probe, lower Z and visa versa.

                    undefined 1 Reply Last reply 24 May 2020, 18:16 Reply Quote 0
                    • undefined
                      1ri @observatoer
                      last edited by 1ri 24 May 2020, 18:16

                      @observatoer
                      Considering that you have the z-probe fine Tuned and configured. You commented that you have the problem when you do the homing. Is it possible that you do not use the z-probe to set z=0 and that there is this difference of one millimeter between the z-axis sensor and the z-probe?

                      In my printer, with dual z axis, after home with micros witches every motor, I run a G30 command to set Z=0 with de Z-probe then I run a G32 command.

                      It works well for me in reprap 3.1 on a duetWifi+Duex

                      1 Reply Last reply Reply Quote 0
                      • undefined
                        Phaedrux Moderator
                        last edited by 24 May 2020, 18:56

                        Please post your full config.g and homeall.g / homez.g please

                        Z-Bot CoreXY Build | Thingiverse Profile

                        undefined 1 Reply Last reply 24 May 2020, 20:16 Reply Quote 0
                        • undefined
                          observatoer @Phaedrux
                          last edited by 24 May 2020, 20:16

                          @Phaedrux Thanks for the support! Maybe, I figured it out but nor sure about the "how".

                          ; General preferences
                          G90 ; send absolute coordinates...
                          M83 ; ...but relative extruder moves
                          M550 P"Duet 3" ; set printer name
                          G21 ; Work in millimetres
                          M575 P1 B57600 S1 ; Comms parameters for PanelDue
                          M669 K1 ; select CoreXY mode

                          ; Network & Logging
                          M111 S0 ; Debug off
                          M929 P"eventlog.txt" S0 ; Start logging to file eventlog.txt

                          ; Axis and motor configuration

                          M569 P0 S0 ; physical drive 0 goes backwards
                          M569 P1 S0 ; physical drive 1 goes backwards
                          M569 P2 S1 ; physical drive 2 goes forward
                          M569 P3 S0 ; physical drive 3 > Right goes backwards
                          M569 P4 S0 ; physical drive 4 > Left Front goes backwards
                          M569 P5 S0 ; physical drive 5 > Left Back goes backwards

                          M584 X1 Y2 Z3:4:5 E0 ; set drive mapping: Achtung. Z Motoren P3=Z3, P4 = Z4 und P5=Z5!! Sonst funktioniert Leveling nicht.
                          M350 X16 Y16 E16 I1 ; configure microstepping with interpolation
                          M350 Z16 I1 ; z axis isolated
                          M92 E830 ; set steps per mm Extruder
                          M92 X191.883 Y191.883 ; set steps per mm (0.9/16T=200s/mm) calibrated PLA: 190.9286
                          M92 Z3200 ; z axis isolated
                          M203 X24000 Y24000 Z900 E8000 ; set maximum speeds (mm/min)
                          M201 X1000 Y1000 Z40 E1300 ; set accelerations (mm/s^2)
                          M906 X1900 Y1900 Z1600 E650 I5 ; set motor currents (mA) and motor idle factor in per cent
                          M566 X1000 Y1000 Z150 E3000 ; Maximum jerk speeds mm/minute / Jubilee
                          M84 S600 ; Set idle timeout

                          ;Pressure Advance
                          M572 D0 S0.05 ; set pressure advance for extruder 0. Direct Drive recomendation = 0.025

                          ;Leadscrew locations
                          M671 X-10:-10:333 Y22.5:277.5:150 S7.5 ; Front left, Rear Left, Right S7.5 is the max correction - measure your own offsets, to the bolt for the yoke of each leadscrew

                          ; Axis Limits
                          M208 X0 Y0 Z-2 S1 ; set axis minima
                          M208 X305 Y305 Z315 S0 ; set axis maxima

                          ; Z-Probe
                          M558 P8 C"io3.in" H5 F120 T6000 ; Changed from Mode 1 to Mode 8 for IR / set Z probe type to unmodulated and the dive height + speeds
                          G31 P500 X-2 Y26.42 Z1.45 ; set Z probe trigger value, offset and trigger height (DC42)
                          M557 X0:295 Y0:295 S70 ; define mesh grid

                          ; Endstops
                          M574 X1 S1 P"io1.in" ; configure active-high endstop for low end on X via pin io1.in
                          M574 Y1 S1 P"io2.in" ; configure active-high endstop for low end on Y via pin io2.in
                          M574 Z1 S2 ; configure Z-probe endstop for low end on Z

                          ; Heater & Fan
                          M308 S0 P"temp0" A"Heat Bed" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0
                          M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
                          M143 H0 S120 ; set temperature limit for heater 0 to 120C
                          M307 H0 B1 S1.00 ;enable bang-bang mode for the bed heater and set PWM limit
                          M140 H0 ; map heated bed to heater 0

                          M308 S1 P"temp1" A"Slice Hotend" Y"thermistor" T500000 B4723 C1.19622e-7 ; Slice Thermistor: configure sensor 1 as thermistor
                          ; on pin temp1
                          M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
                          M143 H1 S280 ; set temperature limit for heater 1 to 280C
                          M307 H1 B0 S1.00 ; set bang-bang mode for heater

                          ; Fans
                          M950 F0 C"out8" Q500 ; create fan 0 on pin out8 and set its frequency >> Heatsink Fan
                          M106 P0 S0 H1 T45 ; set fan 0 value. Thermostatic control is turned on.
                          M950 F1 C"out9" Q500 ; create fan 1 on pin out9 and set its frequency. >> Part Fan
                          ;;M106 P1 S1 H-1 ; set fan 1 value. Thermostatic control is turned off
                          M106 P1 S1 H1 T45

                          ;Probe points
                          M557 X20:275 Y30:275 P3

                          ; Tools
                          M563 P0 D0 H1 F0 ; define tool 0
                          G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
                          G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

                          ; Tools
                          M563 P0 S"Mosquito Magnum" D0 H1 F0 ; define tool 0
                          G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
                          G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

                          ;M98 P"config-user.g" ; Load custom user config if one exists.

                          ;M501 ; Load saved parameters from non-volatile memory

                          ;G29 S1

                          ; Note: you will need to tune the bed heater, and both extruder cartridges before printing.
                          ; See the following link for more details. https://duet3d.dozuki.com/Wiki/Tuning_the_heater_temperature_control

                          ; Custom settings are not defined

                          ; Miscellaneous
                          M501 ; load saved parameters from non-volatile memory

                          ; homeall.g
                          ; called to home all axes
                          ;
                          ; generated by RepRapFirmware Configuration Tool v2.1.8 on Sat May 16 2020 15:05:51 GMT+0200 (CEST)
                          G91 ; relative positioning
                          G1 H2 Z5 F6000 ; lift Z relative to current position
                          G1 H1 X-305 Y-305 F1800 ; move quickly to X or Y endstop and stop there (first pass)
                          G1 H1 X-305 ; home X axis
                          G1 H1 Y-305 ; home Y axis
                          G1 X5 Y5 F6000 ; go back a few mm
                          G1 H1 X-305 F360 ; move slowly to X axis endstop once more (second pass)
                          G1 H1 Y-305 ; then move slowly to Y axis endstop
                          G1 H1 Z-305 F360 ; move Z down stopping at the endstop
                          G90 ; absolute positioning

                          G92 Z1.60 ; Remark: Adjuted from Z0 to Z1.60 // set Z position to axis minimum (you may want to adjust this)
                          ;G92 Z0 ; set Z position to axis minimum (you may want to adjust this)

                          ; Uncomment the following lines to lift Z after probing
                          G91 ; relative positioning
                          G1 Z5 F100 ; lift Z relative to current position
                          G90 ; absolute positioning

                          ; homez.g
                          ; called to home the Z axis
                          ;
                          ; generated by RepRapFirmware Configuration Tool v2.1.8 on Sat May 16 2020 15:05:51 GMT+0200 (CEST)
                          G91 ; relative positioning
                          G1 H2 Z5 F300 ; lift Z relative to current position
                          G1 H1 Z-305 F300 ; move Z up until the endstop is triggered
                          ;G92 Z0 ; set Z position to axis minimum (you may want to adjust this)
                          G92 Z1.60 ; set Z position to axis minimum (you may want to adjust this)

                          1 Reply Last reply Reply Quote 0
                          • undefined
                            Phaedrux Moderator
                            last edited by 24 May 2020, 22:34

                            Your homing files are using end stops to home Z and not the probe.

                            G1 H1 Z-305 F360 ; move Z down stopping at the endstop
                            G90 ; absolute positioning
                            G92 Z1.60 ; Remark: Adjuted from Z0 to Z1.60 // set Z position to axis minimum (you may want to adjust this)

                            These sections should be replaced with

                            G1 X100 Y100 F6000 ; move probe to center of the bed. Adjust as needed.
                            G30 ; probe the bed to establish z0

                            Z-Bot CoreXY Build | Thingiverse Profile

                            undefined 1 Reply Last reply 25 May 2020, 05:02 Reply Quote 0
                            • undefined
                              observatoer @Phaedrux
                              last edited by 25 May 2020, 05:02

                              @Phaedrux YES! This is the solution. Thank you very much 😳 👍

                              1 Reply Last reply Reply Quote 0
                              12 out of 16
                              • First post
                                12/16
                                Last post
                              Unless otherwise noted, all forum content is licensed under CC-BY-SA