Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    E3D BigBox rebuild - some issues - Duet Wifi

    Scheduled Pinned Locked Moved
    Duet Hardware and wiring
    4
    6
    246
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • TimVundefined
      TimV
      last edited by TimV

      Hi all,
      As you may have noticed, I've restarted my E3D BigBox again.
      This has been fully disassembled, cleaned rewired and rebuild.
      Now I have some issues (after the SD Card issue)

      • Z axis only move in 1 direction, no matter what Direction I push. What may case this,
      • Currently running v 1.19.2, do I stay here, or do I move to another version, and if so, what version would that be.
      • While troubleshooting, I have pushed the reset button on my 7" PanelDue. How to get that fixed, keep in mind, I'm sure this has a direct impact on the version running.
        Most probably other issues might appear, I'll open another post for those once I get to them.
        Thx in advance
        T.
      Vetiundefined Phaedruxundefined 2 Replies Last reply Reply Quote 0
      • Vetiundefined
        Veti @TimV
        last edited by

        @TimV said in E3D BigBox rebuild - some issues - Duet Wifi:

        Z axis only move in 1 direction, no matter what Direction I push. What may case this,

        most likely a bad crimp contact.

        Currently running v 1.19.2, do I stay here, or do I move to another version, and if so, what version would that be.

        if you are starting from scratch go for 3.1.1.

        Since you need to do an bossa update for your paneldue go the bossa route.
        see
        https://duet3d.dozuki.com/Wiki/Installing_and_Updating_Firmware#Section_Fallback_procedure_Num_3

        While troubleshooting, I have pushed the reset button on my 7" PanelDue. How to get that fixed, keep in mind, I'm sure this has a direct impact on the version running.

        see https://duet3d.dozuki.com/Wiki/PanelDue_Firmware_update

        1 Reply Last reply Reply Quote 0
        • TimVundefined
          TimV
          last edited by

          Small update:

          • Z axis work, confirmed was a bad cable connection, easy fix.
          • Flashed PanelDue with 1.2.4 and also ran the verify. All is ok. Bossa port appears etc. But still nothing after fully reconnecting it back to the DuetWifi.
          • Didn't yet do the upgrade to 3.1.1, avoid multiplying the issues.

          So, any advice on how to troubleshoot what's wrong with the PanelDue.
          I hear no beepbeep when the DuetWifi boots (or has finished booting), I have 5v in the pinout, and also 3,3 between GND and 3.3V on the Panel Due V2.0 mini board. and also on JP1 (Gnd and 3.3V pin).
          Cable between DuetWifi and PanelDue has been checked and confirmed correct and working.

          Thx
          T.

          Stephen6309undefined 1 Reply Last reply Reply Quote 0
          • Stephen6309undefined
            Stephen6309 @TimV
            last edited by

            @TimV In config.g, you do have M575 P1 S1 B57600 ?
            The paneldue doesn't beep when the printer boots, unless you've coded that in config.g.

            TimVundefined 1 Reply Last reply Reply Quote 0
            • TimVundefined
              TimV @Stephen6309
              last edited by TimV

              @Stephen6309 yes I have

              M575 P1 B57600 S1
              

              In config.g - 1st line after setting up wifi.

              1 Reply Last reply Reply Quote 0
              • Phaedruxundefined
                Phaedrux Moderator @TimV
                last edited by

                @TimV said in E3D BigBox rebuild - some issues - Duet Wifi:

                Currently running v 1.19.2,

                At least update to 2.05.1. Here are some instructions to update from such an old firmware.

                https://forum.duet3d.com/topic/18962/firmware-not-updating?_=1609006045448

                Z-Bot CoreXY Build | Thingiverse Profile

                1 Reply Last reply Reply Quote 0
                • First post
                  Last post
                Unless otherwise noted, all forum content is licensed under CC-BY-SA