Navigation

    Duet3D Logo

    Duet3D

    • Register
    • Login
    • Search
    • Categories
    • Tags
    • Documentation
    • Order

    External 5V does not power up te board

    Duet Hardware and wiring
    2
    9
    51
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • 3dyorick
      3dyorick last edited by 3dyorick

      Ik have my 12v 350w ATX PSU connected to my duet2wifi
      Therefore i connected thé 12v cables to thé main power supply,
      Thé purple cable to thé 5v_in thé green to thé ps_on and connecteda gnd. (All 3 on thé pins next to main power supply)
      Then i switches thé Jumper tob external 5v_in.

      Ik do measure 5v between 5v_in and gnd but thé board (wifi) does not start up

      If it short between ps_on and gnd, thé 12v does start up thé board (but not thé wifi since they Jumper is mover)

      What do it miss here?

      1 Reply Last reply Reply Quote 0
      • A Former User
        A Former User last edited by

        Have you removed JP9 / I_5V_EN and placed a jumper on JP10 / E_5V_EN?

        See https://duet3d.dozuki.com/Wiki/Power_Wiring#Section_5V_Options for details

        3dyorick 1 Reply Last reply Reply Quote 0
        • 3dyorick
          3dyorick @Guest last edited by

          @bearer yes i did

          1 Reply Last reply Reply Quote 0
          • A Former User
            A Former User last edited by

            Does it power up from USB?

            Take a close look at D14
            f6a922fa-7c61-4068-945e-c2f2acb9df98-image.png

            3dyorick 1 Reply Last reply Reply Quote 0
            • 3dyorick
              3dyorick @Guest last edited by

              @bearer it does start up from USB, what al i looking at?

              1 Reply Last reply Reply Quote 0
              • A Former User
                A Former User last edited by

                If the jumper is set and it works from USB then the diode D14 is the only possible fault as far as I can tell.

                However it might not be possible to visually spot a defect. A well lit close up picture might enable someone to spot something.

                However, you could move the 5v stand by from the 3pin PS_ON connector to any of the other pins labeled 5V on the wiring diagram as a work around. I think I would have used the pin on the E_5V_EN jumper furtherst away from the bed fuse and Vin connector, as it won't be needed for anything else. Please note if you do that, you are loosing the reverse polarity and back feeding protection the diode was meant to offer.

                1 Reply Last reply Reply Quote 0
                • A Former User
                  A Former User last edited by

                  Oh, and if its a genuine duet purchased from an authorized reseller within the last 6 months, then I would see if it qualified for a warranty replacement before doing anything particularly unorthodox.

                  3dyorick 1 Reply Last reply Reply Quote 0
                  • 3dyorick
                    3dyorick @Guest last edited by

                    @bearer that worked, thanks man.
                    Board is over a year old now, so na waranty there.

                    1 Reply Last reply Reply Quote 0
                    • A Former User
                      A Former User last edited by

                      Happy to help! Just for curiosity I'd like to see a picture of the diode if/when you have time; in case its possible to see whats wrong with the diode or soldering of the diode.

                      1 Reply Last reply Reply Quote 0
                      • First post
                        Last post
                      Unless otherwise noted, all forum content is licensed under CC-BY-SA