Board not connect post firm upgrade
-
If you press the Erase button for one second and then press the Reset button, does the Bossa Port appear in the COM port listing?
-
Yes,
-
I try a few times more with bossa and cant connect with pronterface or repetier after flash. Board continues resetting past 1 min, windows blip the sound of the com connecting and disconnecting.
-
Check the size of the firmware file you downloaded and are flashing to the Duet. It should be around 300kbytes.
After a successful firmware update, check how the Duet shows up in Device Manager. You may need to install the new device driver from https://github.com/dc42/RepRapFirmware/tree/dev/Driver before you can access it.
-
I will try in a few hours. I use 3 firms, 2 1.18 downloaded well with the same size and the last firm I have, 1.17.
-
Check the size of the firmware file you downloaded and are flashing to the Duet. It should be around 300kbytes.
After a successful firmware update, check how the Duet shows up in Device Manager. You may need to install the new device driver from https://github.com/dc42/RepRapFirmware/tree/dev/Driver before you can access it.
Yes, i see ok
But its rebooting every 20 seconds.
-
Update: without the sdcard dont reboot, its stable. But when i send m552 s1 the reboot its back.
-
I try another sd card and duet its rebooting when the sd card is present in the boot, if i put before no reboots but can use the comand M997 S1 or M552 S1 (this last makes a reboot)
-
Update #759
I finally delete all the sd and only leave a /sys folder with the firmware parts, the duet dont reboot with this sd inserted end i can do this
Connecting…
Printer is now online.M997 S1
SENDING:M997 S1
Trying to connect at 460800 baud:
success
Erasing 290848 bytes...
Uploading file...
5% complete
10% complete
15% complete
20% complete
25% complete
30% complete
35% complete
40% complete
45% complete
50% complete
55% complete
60% complete
65% complete
70% complete
75% complete
80% complete
85% complete
90% complete
95% complete
Upload successful
M997 S2
SENDING:M997 S2
Trying to connect at 460800 baud:
success
Erasing 3125248 bytes...
Uploading file...
5% complete
10% complete
15% complete
20% complete
25% complete
30% complete
35% complete
40% complete
45% complete
50% complete
55% complete
60% complete
65% complete
70% complete
75% complete
80% complete
85% complete
90% complete
95% complete
Upload successful
m552 s1
SENDING:M552 S1
WiFi server starting up
DuetWiFiServer version 1.03 (ch fork)
Flash size 4194304, free RAM 32840 bytes, WiFi Vcc 3.03V, host name: duetwifi1, reset reason: Turned on by main processor
WiFi server connected to access point CAT1, IP=192.168.1.10, signal strength=-52dBm
My god, why always have problems whit the **** wifi module?
-
Looks like you've made progress! Edit your config.g file, commenting out the M552 S1 line. Then it should boot up OK, with WiFi disabled. Then install new WiFi firmware by copying the DuetWiFiServer file to the SD card, renaming it to exactly DuetWiFiServer.bin, and use M997 S1 to install it. If you've installed main firmware 1.18.2 then the correct WiFi firmware version to use is 1.03-ch.
EDIT: you got there first.
-
No, with the config.g empy or with any caracter dont boot ok, always reboot. First thing i do was comment the m552.
Now i will put back the duet in the printer, prints like none has passed.
