Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Heater scale at 2000 degrees

    Scheduled Pinned Locked Moved
    General Discussion
    2
    15
    440
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Phaedruxundefined
      Phaedrux Moderator
      last edited by

      Post your full config please.

      Z-Bot CoreXY Build | Thingiverse Profile

      1 Reply Last reply Reply Quote 0
      • cdthomas9undefined
        cdthomas9
        last edited by

        ; General preferences
        M111 S0 ; Debugging off
        G21 ; Work in millimetres
        G90 ; Send absolute coordinates...
        M83 ; ...but relative extruder moves
        M555 P2 ; Set firmware compatibility to look like Marlin
        M208 X-7 Y0 Z0 S1 ; Set axis minima
        M208 X252 Y153 Z155 S0 ; Set axis maxima (reduced by offset above)

        ; Enable Panel Due Connector
        M575 P1 S1 B57600 ; Enables connector and sets baud rate

        ; Endstops
        M574 X1 S1 P"!xstop" ; X min active high endstop switch
        M574 Y1 S1 P"!ystop" ; Y min active high endstop switch

        ;Manual Bed Leveling
        M558 P9 C"^zprobe.in" H5 F500 T4000 X0 Y0 Z1 ; Set Z probe type/mode 9. H=Dive Height. F=Speed the bed moves
        G31 P25 X-36 Y0 Z2.885 ; Z probe trigger value, offset in relation to nozzle. And trigger height adjustment
        M557 X40:190 Y20:145 S20 ; Define mesh grid
        ;M671 x144:94:191 Y10:160:160 P0.5 ; Manual screw adjustment locations

        ; Drives
        M569 P0 S1 ; Drive 0 goes backwards
        M569 P1 S1 ; Drive 1 goes backwards
        M569 P2 S0 ; Drive 2 goes forwards
        M569 P3 S0 ; Drive 3 goes forwards
        M569 P4 S1 ; Drive 4 goes backwards
        M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
        M92 X88.573186 Y88.573186 Z400 E96.27520187033366 ; Set steps per mm
        M566 X900 Y900 Z300 E1200 ; Set maximum instantaneous speed changes (mm/min)
        M203 X1080000 Y1080000 Z600 E96000 ; Set maximum speeds (mm/min)
        M201 X1000 Y1000 Z100 E2000 ; Set accelerations (mm/s^2)
        M906 X800 Y800 Z400 E800 I30 ; Set motor currents (mA) and motor idle factor in per cent
        M84 S30 ; Set idle timeout
        M584 X0 Y1 Z2 E3:4 ; Set drive assignments

        ; Heaters
        M140 H0
        M143 S260 ; Set maximum heater temperature to 260C
        M308 S0 P"bed_temp" Y"thermistor" T100000 B3974 C0 R4700 ; Set thermistor + ADC parameters for heater 0
        M308 S1 P"e0_temp" Y"thermistor" T100000 B4725 C7.060000e-8 R4700 ; Set thermistor + ADC parameters for heater 1
        M308 S2 P"e1_temp" Y"thermistor" T100000 B4725 C7.060000e-8 R4700 ; Set thermistor + ADC parameters for heater 2
        M950 H0 C"bed_heat" T0 ; heater 0 uses the bed_heat pin, sensor 0
        M950 H1 C"e0_heat" T1 ; heater 1 uses the e0_heat pin and sensor 1
        M950 H2 C"e1_heat" T2 ; heater 2 uses the e1_heat pin and sensor 2
        M307 H0 A103.7 C787.7 D1.0 S1.00 B0
        ;M307 H0 A38.5 C41.1 D1.4 V24.4 B0 ; Set PID values for Heatedbed - derived from autotune
        M307 H1 A250.2 C139.5 D5.4 V24.4 B0 ; Set PID values for Extruder 1 - derived from autotune
        M307 H2 A387.6 C209.9 D5.9 V24.4 B0 ; Set PID values for Extruder 2 - derived from autotune
        M307 H3 A-1 C-1 D-1 ; Disable the 4th Heater to free up PWM channel on the Duex board.

        ; Tools
        M563 P0 D0 H1 ; Define tool 0
        G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
        G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
        M563 P1 D1 H2 ; Define tool 1
        G10 P1 X34 Y0 Z0 ; Set tool 1 axis offsets
        G10 P1 R0 S0 ; Set initial tool 1 active and standby temperatures to 0C
        M207 S1.2 F1200 ; Set 1.2mm retract distance for G10 command

        ; Network
        M550 P"Rep2X-EnStein" ; Set machine name
        M552 S1 ; Enable network
        M586 P0 S1 ; Enable HTTP
        M586 P1 S1 ; Enable FTP
        M586 P2 S0 ; Disable Telnet

        ; Fans
        M950 F0 C"fan0" Q500 ; Set fan 0 value, PWM signal inversion and frequency.
        M950 F1 C"fan2" Q500 ; Set fan 1 value, PWM signal inversion and frequency.
        M106 P0 T40:50 H1 ; Set fan 0. Thermostatic control is turned on
        M106 P1 T40:50 H2 ; Set fan 1. Thermostatic control is turned on
        M950 S0 C"exp.heater3" ; Define BLTouch probe

        M564 H0 ; Allow Movement while axes are NOT homed

        1 Reply Last reply Reply Quote 0
        • Phaedruxundefined
          Phaedrux Moderator
          last edited by

          @cdthomas9 said in Heater scale at 2000 degrees:

          ; Heaters
          M140 H0
          M143 S260 ; Set maximum heater temperature to 260C
          M308 S0 P"bed_temp" Y"thermistor" T100000 B3974 C0 R4700 ; Set thermistor + ADC parameters for heater 0
          M308 S1 P"e0_temp" Y"thermistor" T100000 B4725 C7.060000e-8 R4700 ; Set thermistor + ADC parameters for heater 1
          M308 S2 P"e1_temp" Y"thermistor" T100000 B4725 C7.060000e-8 R4700 ; Set thermistor + ADC parameters for heater 2
          M950 H0 C"bed_heat" T0 ; heater 0 uses the bed_heat pin, sensor 0
          M950 H1 C"e0_heat" T1 ; heater 1 uses the e0_heat pin and sensor 1
          M950 H2 C"e1_heat" T2 ; heater 2 uses the e1_heat pin and sensor 2
          M307 H0 A103.7 C787.7 D1.0 S1.00 B0
          ;M307 H0 A38.5 C41.1 D1.4 V24.4 B0 ; Set PID values for Heatedbed - derived from autotune
          M307 H1 A250.2 C139.5 D5.4 V24.4 B0 ; Set PID values for Extruder 1 - derived from autotune
          M307 H2 A387.6 C209.9 D5.9 V24.4 B0 ; Set PID values for Extruder 2 - derived from autotune
          M307 H3 A-1 C-1 D-1 ; Disable the 4th Heater to free up PWM channel on the Duex board.

          You only have one M143. You must set it for each heater.

          https://duet3d.dozuki.com/Wiki/Gcode?revisionid=HEAD#Section_M143_in_RRF_3_01RC2_and_later

          Z-Bot CoreXY Build | Thingiverse Profile

          1 Reply Last reply Reply Quote 0
          • cdthomas9undefined
            cdthomas9
            last edited by

            So remove the M143 I have and add in this?

            M143 H0 P0 S160 T0 A2
            M143 H1 P1 S290 T1 A2
            M143 H2 P2 S290 T2 A2

            1 Reply Last reply Reply Quote 0
            • Phaedruxundefined
              Phaedrux Moderator
              last edited by

              Looks ok

              Z-Bot CoreXY Build | Thingiverse Profile

              1 Reply Last reply Reply Quote 0
              • cdthomas9undefined
                cdthomas9
                last edited by

                I still get the same scale. I can see that it changes to a max of 300 degrees for a second, when restarting the board, but then it jumps to 2000 again.

                1 Reply Last reply Reply Quote 0
                • Phaedruxundefined
                  Phaedrux Moderator
                  last edited by

                  What firmware and DWC version?

                  Can you post your changed config.g?

                  Z-Bot CoreXY Build | Thingiverse Profile

                  1 Reply Last reply Reply Quote 0
                  • cdthomas9undefined
                    cdthomas9
                    last edited by

                    ; General preferences
                    M111 S0																	; Debugging off
                    G21																		; Work in millimetres
                    G90																		; Send absolute coordinates...
                    M83																		; ...but relative extruder moves
                    M555 P2																	; Set firmware compatibility to look like Marlin
                    M208 X-7 Y0 Z0 S1														; Set axis minima 
                    M208 X252 Y153 Z155 S0													; Set axis maxima (reduced by offset above)
                    
                    ; Enable Panel Due Connector
                    M575 P1 S1 B57600														; Enables connector and sets baud rate
                    
                    ; Endstops
                    M574 X1 S1 P"!xstop"													; X min active high endstop switch
                    M574 Y1 S1 P"!ystop"													; Y min active high endstop switch
                    
                    ;Manual Bed Leveling
                    M558 P9 C"^zprobe.in" H5 F500 T4000 X0 Y0 Z1							; Set Z probe type/mode 9. H=Dive Height. F=Speed the bed moves
                    G31 P25 X-36 Y0 Z2.885													; Z probe trigger value, offset in relation to nozzle. And trigger height adjustment
                    M557 X40:190 Y20:145 S20												; Define mesh grid
                    ;M671 x144:94:191 Y10:160:160 P0.5 										; Manual screw adjustment locations 
                    
                    ; Drives
                    M569 P0 S1																; Drive 0 goes backwards
                    M569 P1 S1																; Drive 1 goes backwards
                    M569 P2 S0																; Drive 2 goes forwards
                    M569 P3 S0																; Drive 3 goes forwards
                    M569 P4 S1																; Drive 4 goes backwards
                    M350 X16 Y16 Z16 E16 I1													; Configure microstepping with interpolation
                    M92 X88.573186 Y88.573186 Z400 E96.27520187033366						; Set steps per mm
                    M566 X900 Y900 Z300 E1200												; Set maximum instantaneous speed changes (mm/min)
                    M203 X1080000 Y1080000 Z600 E96000										; Set maximum speeds (mm/min)
                    M201 X1000 Y1000 Z100 E2000												; Set accelerations (mm/s^2)
                    M906 X800 Y800 Z400 E800 I30											; Set motor currents (mA) and motor idle factor in per cent
                    M84 S30 																; Set idle timeout
                    M584 X0 Y1 Z2 E3:4														; Set drive assignments
                    
                    ; Heaters
                    M140 H0
                    M143 H0 P0 S160 T0 A2													; Set maximum bed heater temperature to 160C
                    M143 H1 P1 S290 T1 A2													; Set maximum heater 1 temperature to 290C
                    M143 H2 P2 S290 T2 A2													; Set maximum heater 2 temperature to 290C
                    M308 S0 P"bed_temp" Y"thermistor" T100000 B3974 C0 R4700				; Set thermistor + ADC parameters for heater 0
                    M308 S1 P"e0_temp" Y"thermistor" T100000 B4725 C7.060000e-8 R4700		; Set thermistor + ADC parameters for heater 1
                    M308 S2 P"e1_temp" Y"thermistor" T100000 B4725 C7.060000e-8 R4700		; Set thermistor + ADC parameters for heater 2
                    M950 H0 C"bed_heat" T0													; heater 0 uses the bed_heat pin, sensor 0
                    M950 H1 C"e0_heat" T1													; heater 1 uses the e0_heat pin and sensor 1
                    M950 H2 C"e1_heat" T2													; heater 2 uses the e1_heat pin and sensor 2
                    M307 H0 A103.7 C787.7 D1.0 S1.00 B0
                    ;M307 H0 A38.5 C41.1 D1.4 V24.4 B0										; Set PID values for Heatedbed - derived from autotune
                    M307 H1 A250.2 C139.5 D5.4 V24.4 B0										; Set PID values for Extruder 1 - derived from autotune
                    M307 H2 A387.6 C209.9 D5.9 V24.4 B0										; Set PID values for Extruder 2 - derived from autotune
                    M307 H3 A-1 C-1 D-1														; Disable the 4th Heater to free up PWM channel on the Duex board.
                    
                    ; Tools
                    M563 P0 D0 H1															; Define tool 0
                    G10 P0 X0 Y0 Z0															; Set tool 0 axis offsets
                    G10 P0 R0 S0															; Set initial tool 0 active and standby temperatures to 0C
                    M563 P1 D1 H2															; Define tool 1
                    G10 P1 X34 Y0 Z0														; Set tool 1 axis offsets
                    G10 P1 R0 S0															; Set initial tool 1 active and standby temperatures to 0C
                    M207 S1.2 F1200															; Set 1.2mm retract distance for G10 command
                    
                    ; Network
                    M550 P"Rep2X-EnStein"													; Set machine name
                    M552 S1																	; Enable network
                    M586 P0 S1																; Enable HTTP
                    M586 P1 S1																; Enable FTP
                    M586 P2 S0																; Disable Telnet
                    
                    ; Fans
                    M950 F0 C"fan0" Q500													; Set fan 0 value, PWM signal inversion and frequency.
                    M950 F1 C"fan2" Q500													; Set fan 1 value, PWM signal inversion and frequency.
                    M106 P0 T40:50 H1														; Set fan 0. Thermostatic control is turned on
                    M106 P1 T40:50 H2														; Set fan 1. Thermostatic control is turned on
                    M950 S0 C"exp.heater3"													; Define BLTouch probe
                    
                    
                    M564 H0 ; Allow Movement while axes are NOT homed
                    
                    1 Reply Last reply Reply Quote 0
                    • cdthomas9undefined
                      cdthomas9
                      last edited by cdthomas9

                      DWC 3.2.0
                      Duet 2 WiFi/Ethernet 3.2 (2021-01-05)
                      Duet WiFi Server Version: 1.25

                      1 Reply Last reply Reply Quote 0
                      • cdthomas9undefined
                        cdthomas9
                        last edited by

                        I recently updated to 3.2 for DWC and the firmware, could there be something in DWC I need to change?

                        1 Reply Last reply Reply Quote 0
                        • Phaedruxundefined
                          Phaedrux Moderator
                          last edited by

                          The order of heater commands does matter. You've got them all clumped together.

                          I suggest you re-order your commands to group them by heater number rather than command type.

                          Here's an example from the configurator:

                          ; Heaters
                          M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
                          M950 H0 C"bedheat" T0                          ; create bed heater output on bedheat and map it to sensor 0
                          M307 H0 B0 S1.00                               ; disable bang-bang mode for the bed heater and set PWM limit
                          M140 H0                                        ; map heated bed to heater 0
                          M143 H0 S120                                   ; set temperature limit for heater 0 to 120C
                           
                          M308 S1 P"e0temp" Y"thermistor" T100000 B4138  ; configure sensor 1 as thermistor on pin e0temp
                          M950 H1 C"e0heat" T1                           ; create nozzle heater output on e0heat and map it to sensor 1
                          M307 H1 B0 S1.00                               ; disable bang-bang mode for heater  and set PWM limit
                          M143 H1 S280                                   ; set temperature limit for heater 1 to 280C
                           
                          M308 S2 P"e1temp" Y"thermistor" T100000 B4138  ; configure sensor 2 as thermistor on pin e1temp
                          M950 H2 C"e1heat" T2                           ; create chamber heater output on e1heat and map it to sensor 2
                          M307 H2 B0 S1.00                               ; disable bang-bang mode for the chamber heater and set PWM limit
                          M141 H2                                        ; map chamber to heater 2
                          M143 H2 S280                                   ; set temperature limit for heater 2 to 280C
                          

                          Z-Bot CoreXY Build | Thingiverse Profile

                          1 Reply Last reply Reply Quote 0
                          • cdthomas9undefined
                            cdthomas9
                            last edited by

                            Perfect, thanks!

                            1 Reply Last reply Reply Quote 0
                            • First post
                              Last post
                            Unless otherwise noted, all forum content is licensed under CC-BY-SA