Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Duet resetting when using air pump

    Scheduled Pinned Locked Moved
    Duet Hardware and wiring
    7
    38
    5.0k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • tomasfundefined
      tomasf
      last edited by

      So my new pump arrived. The very same kind. I soldered on the diode and connected it and… same thing. Duet resets.

      If I connect the pump directly to the 24V output of the supply, Duet resets. However, if I also disconnect Duet's VIN+GND terminals so that the pump is alone on the higher voltage, Duet does not reset. Re-connecting the high-power GND terminal restores the previous behaviour. I'm not sure what to make of this.

      1 Reply Last reply Reply Quote 0
      • fmaundefined
        fma
        last edited by

        Is the motor close to the Duet? It might be an interference issue when the motor runs.

        Did you try to use a separate power supply, and drive it through a FET?

        Frédéric

        1 Reply Last reply Reply Quote 0
        • dc42undefined
          dc42 administrators
          last edited by

          Is the metal casing of the pump motor in contact with anything?

          Duet WiFi hardware designer and firmware engineer
          Please do not ask me for Duet support via PM or email, use the forum
          http://www.escher3d.com, https://miscsolutions.wordpress.com

          1 Reply Last reply Reply Quote 0
          • tomasfundefined
            tomasf
            last edited by

            @fma:

            Is the motor close to the Duet? It might be an interference issue when the motor runs.

            Did you try to use a separate power supply, and drive it through a FET?

            The motor is currently outside the printer frame with a ~15 cm cable. Before, I used a 60+ cm wire and the pump far outside the printer with the same result.

            I have tried using a separate supply operated manually, but not with a FET. Good idea, I should try that. I guess the two supplies would need a common GND connection. I just hope that connection doesn't spread whatever happens to the Duet again.

            It's so frustrating. If I only knew what's actually happening, I might be able to solve it. Now I'm just clueless.

            1 Reply Last reply Reply Quote 0
            • tomasfundefined
              tomasf
              last edited by

              @dc42:

              Is the metal casing of the pump motor in contact with anything?

              Nope. It's currently free on a wooden table, and normally it lives isolated in a plastic case.

              1 Reply Last reply Reply Quote 0
              • Alexander Mundyundefined
                Alexander Mundy
                last edited by

                Gasping at straws here. Just out of curiousity, have you tried running it with the separate supply electrically isolated completely from the duet and it's supply? I don't understand how it could be, but that would only leave EMI as the cause.

                1 Reply Last reply Reply Quote 0
                • tomasfundefined
                  tomasf
                  last edited by

                  @Alexander:

                  Gasping at straws here. Just out of curiousity, have you tried running it with the separate supply electrically isolated completely from the duet and it's supply? I don't understand how it could be, but that would only leave EMI as the cause.

                  Yeah, that's what I'm doing now, and it works fine.
                  My printer's power supply also works for the pump as long as Duet's VIN (or rather, the VIN GND) isn't connected to that supply, it seems.

                  1 Reply Last reply Reply Quote 0
                  • Dougal1957undefined
                    Dougal1957
                    last edited by

                    that sound like a ground loop issue now you've said that

                    1 Reply Last reply Reply Quote 0
                    • dc42undefined
                      dc42 administrators
                      last edited by

                      Do you have the Duet connected to as PC via USB as well?

                      Duet WiFi hardware designer and firmware engineer
                      Please do not ask me for Duet support via PM or email, use the forum
                      http://www.escher3d.com, https://miscsolutions.wordpress.com

                      1 Reply Last reply Reply Quote 0
                      • Alexander Mundyundefined
                        Alexander Mundy
                        last edited by

                        Check the polarity of each power supply input and also anything that is connected via a cable. Make sure that the intentionally grounded AC conductor (commonly called the neutral here in the US) is hooked to the power supplys as they should be. A reverse polarity on one could account for this.

                        1 Reply Last reply Reply Quote 0
                        • dc42undefined
                          dc42 administrators
                          last edited by

                          What power supply are you using to drive the Duet and the pump motor?

                          Duet WiFi hardware designer and firmware engineer
                          Please do not ask me for Duet support via PM or email, use the forum
                          http://www.escher3d.com, https://miscsolutions.wordpress.com

                          1 Reply Last reply Reply Quote 0
                          • First post
                            Last post
                          Unless otherwise noted, all forum content is licensed under CC-BY-SA