Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Heater Fault

    Scheduled Pinned Locked Moved
    Tuning and tweaking
    3
    8
    1.6k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Martin_Sundefined
      Martin_S
      last edited by

      This error happens occasionally, today is one of those days.
      I set the temperature to lets say 230ºc, it reaches, gets stable and then hit "Start Print". When the hotend it's about to print the first layer, the temperature raises instantly from 230ºc to 255ºc and the heater goes into fault mode. I doubt that in less than one second it could jump that high.

      What's going on here? My only solution is to hit emergency stop and then try again.
      This usually does the trick, but I've already tried 2 times and it keeps happening.

      Thoughts?

      Firmware Electronics: 	Duet WiFi 1.0
      Firmware Version: 	1.20beta6 (2017-11-03)
      WiFi Server Version: 	1.20beta2
      Web Interface Version: 	1.19.3
      ``` 
      
      Thanks.
      Martin

      If it ain't broke, fix it till it is =)

      1 Reply Last reply Reply Quote 0
      • KeeganBundefined
        KeeganB
        last edited by

        This is common of a failing thermistor, or a short. Heat it to temp and carefully wiggle the wiring and see if you get any jumps in the graph on DWC (or faults).

        Artemis
        Rostock Max v2
        Orion

        1 Reply Last reply Reply Quote 0
        • Martin_Sundefined
          Martin_S
          last edited by

          Will do, thanks.

          If it ain't broke, fix it till it is =)

          1 Reply Last reply Reply Quote 0
          • Martin_Sundefined
            Martin_S
            last edited by

            3rd try was the victorious. It printed fine.

            I've tried moving the wiring at different locations but couldn't reproduce the same error.

            I was hopping this was a firmware issue.
            Will try with another thermistor and see how it goes.

            If it ain't broke, fix it till it is =)

            1 Reply Last reply Reply Quote 0
            • Martin_Sundefined
              Martin_S
              last edited by

              I think it had to do with the thermistor picking up interference from the extruder motor cables, but that's something I read somewhere else. The wiring is not shielded so it could be it. Either way, it didn't happen again.

              The real reason for this post is for someone to explain me what's going on with this test.
              I was having some problems when trying to extrude filament at a certain temperature. So I grabbed the digital thermometer and started comparing measurements.

              The M3 grub screw that was holding the thermistor was removed. Placed in there the thermocouple.
              I think that's the best place for comparing both readings, as they are practically next to each other.

              Thermistor used: Semitec 104GT, cartridge style version from E3D.
              Config.g value: M305 P1 T100000 B4725 C7.06e-8 R4700
              Testing device: TM902C Thermometer with a Type-K thermocouple. (Yes, not the best one, but it should be more accurate than a thermistor)

              First column: This is the target temperature set in the DWC.
              Second column: Temperature readings from the thermometer. Using here a 12v power supply feeding the Duet.
              Third column: Temperature difference.

              First column: This is the target temperature set in the DWC.
              Second column: Temperature readings from the thermometer. Using here a 24v power supply feeding the Duet.
              Third column: Temperature difference.

              I expected some discrepancies with the temperature, but what's weird is that the readings when the Duet is fed by a 12v PSU differ from when it's fed by a 24v PSU.

              Is this normal? or is it necesary to adjust the B or C parameter for better accuracy?
              Why would a thermistor care about voltage? The temperature accuracy seems more accurate with 24v than with 12v, but only at certain points.

              If someone could shed a light in here it would be much appreciated.

              If it ain't broke, fix it till it is =)

              1 Reply Last reply Reply Quote 0
              • dc42undefined
                dc42 administrators
                last edited by

                The power supply voltage shouldn't affect the reading. I suspect something else caused different readings on your two runs.

                Duet WiFi hardware designer and firmware engineer
                Please do not ask me for Duet support via PM or email, use the forum
                http://www.escher3d.com, https://miscsolutions.wordpress.com

                1 Reply Last reply Reply Quote 0
                • Martin_Sundefined
                  Martin_S
                  last edited by

                  Thanks David, you might be right.
                  Too bad I don't have a spare cartridge thermistor replacement atm, most certainly it's a faulty thermistor causing this.
                  I was going to buy one, but maybe it's time for an upgrade.

                  PT100 would be a good choice? If so, is this all that's needed for the upgrade?:

                  • E3D PT100 sensor
                  • Duet PT100 daughterboard

                  or better to go with a Type-K thermocouple?

                  If it ain't broke, fix it till it is =)

                  1 Reply Last reply Reply Quote 0
                  • dc42undefined
                    dc42 administrators
                    last edited by

                    I recommend PT100 sensors over thermocouples, except where very high temperatures are required. The E3D PT100 sensor (without the amplifier board) and Duet PT100 daughter board are sufficient.

                    Duet WiFi hardware designer and firmware engineer
                    Please do not ask me for Duet support via PM or email, use the forum
                    http://www.escher3d.com, https://miscsolutions.wordpress.com

                    1 Reply Last reply Reply Quote 0
                    • First post
                      Last post
                    Unless otherwise noted, all forum content is licensed under CC-BY-SA