Cancelled printing file, 'abort' command executed

[thaug29]

probe-screw-5sc.gcode I just updated to 3.5.0-rc2 from 3.4.6, I have a 6HC with 1LC v1.3 everything was running fine on 3.4.6 but now the print aborts just after the bed reaches temp. I am using Simplify3D. The error message is

Cancelled printing file 0:/gcodes/probe-screw-5sc.gcode, print time was 0h 1m
'abort' command executed

[oliof]

@thaug29 best to share the file referenced in the error message

[thaug29]

@oliof Which file should I include?

[thaug29]

I moved back to 3.4.6 and everything works fine. I went through the change log for 3.5.0 and I don't see anything that would cause it not to work on my printer. Any ideas what might have changed between the two versions to cause the print to abort after heating the bed. For some reason I am unable to upload my code or file to this site.

[droftarts]

@thaug29 said in Cancelled printing file, 'abort' command executed:

For some reason I am unable to upload my code or file to this site.

It's probably bigger than the file size limit (I'm not sure what that is, though). We only really need to see the first 100 or so lines, up to the first lines of Gcode of the first layer, so you could could copy that from the Gcode (open it in a text editor) and paste it into your reply. Without that... no idea.

Ian

[thaug29]

@droftarts;
This is my startup script.

M104 S140 ; PreHeat nozzle
M109 S140 ; wait for extruder temp
M98 P"/macros/start_print.g"
M104 S[extruder0_temperature] T0 ; set extruder temp
M109 S[extruder0_temperature] T0 ; wait for extruder temp
G1 X20 Y10 Z0.2 F3000 ; get ready to prime
G92 E0 ; reset extrusion distance
G1 X250 E25 F600 ; prime nozzle

This is the G-Code I am trying to print, it heats the bed and then aborts.

G-Code generated by Simplify3D(R) Version 5.1.2
; Jan 25, 2024 at 10:48:44 AM

G90
M82
M106 S0 P0
M140 S105
M190 S105
M104 S140 T0 ; PreHeat nozzle
M109 S140 T0 ; wait for extruder temp
M98 P"/macros/start_print.g"
M104 S220 T0 ; set extruder temp
M109 S220 T0 ; wait for extruder temp
G1 X20 Y10 Z0.2 F3000 ; get ready to prime
G92 E0 ; reset extrusion distance
G1 X250 E25 F600 ; prime nozzle
; process Process 1
; layer 1, Z = 0.2200
T0
G92 E0.00000
G1 E-2.00000 F2100
; feature skirt
; tool H0.2200 W0.480
G1 Z0.2200 F1800
G1 X105.424 Y127.392 F15000
G92 E0.00000
G1 E2.00000 F2100
G92 E0.00000
G1 X127.902 Y136.843 E1.37821

[droftarts]

@thaug29 what is in /macros/start_print.g ? That is called right after bed and hot end get to temperature.

Ian

[thaug29]

@droftarts
These macros run when individually run.

; Macro print start
; reset baby stepping
M290 S0.00 R0

G28

M98 P"/macros/magprobe_do_QGL.g"

G28 Z
G1 Y270

M98 P"/macros/nozzle_scrub.g"

M98 P"/macros/autoz/autoz.g"

; Final settings before print actually start
T0 ; select tool 0
G21 ; set units to mm
M83 ; set extruder to relative mode
G92 E0.0 ; reset extruder position
M220 S100 ; reset speed multiplier

M98 P"/macros/magprobe_dock.g"

echo "Print will now start"

[oliof]

@thaug29 said in Cancelled printing file, 'abort' command executed:

M98 P"/macros/magprobe_do_QGL.g"
M98 P"/macros/nozzle_scrub.g"
M98 P"/macros/autoz/autoz.g"
M98 P"/macros/magprobe_dock.g"

whats in these ones?

[thaug29]

@oliof Thanks for your help but I'm going to stick with 3.4.6 for now and try to simplify and rewrite my macros at a latter time.