I'm a little unsure why but after fiddling around with the bed structure and rerunning all of a suddenly my issue has disappeared. A wild guess is that it was over constrained and deforming. I only put 4 of the 16 screws back. Bed level is better now. Error disappeared. First layer print is successful.
Thanks for the help anyway.
I'm a little unsure why but after fiddling around with the bed structure and rerunning all of a suddenly my issue has disappeared. A wild guess is that it was over constrained and deforming. I only put 4 of the 16 screws back. Bed level is better now. Error disappeared. First layer print is successful.
Thanks for the help anyway.
M98 P"config.g" is not giving me any feedback after M122
Oeps: sorry:
M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.4.2 (2022-09-13 15:11:16) running on Duet WiFi 1.02 or later + DueX5v0.11
Board ID: 0JD0M-9X6JA-JUNSN-6JTDL-3SS6L-KTPBS
Used output buffers: 1 of 26 (26 max)
=== RTOS ===
Static ram: 23860
Dynamic ram: 76728 of which 0 recycled
Never used RAM 8492, free system stack 132 words
Tasks: NETWORK(ready,12.6%,237) HEAT(notifyWait,0.0%,317) Move(notifyWait,0.0%,304) DUEX(notifyWait,0.0%,24) MAIN(running,86.7%,438) IDLE(ready,0.7%,30), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:01:55 ago, cause: software
Last software reset at 2022-12-07 12:11, reason: User, GCodes spinning, available RAM 8524, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x0c
Aux0 errors 0,1,0
Step timer max interval 0
MCU temperature: min 26.2, current 27.1, max 27.3
Supply voltage: min 23.8, current 24.0, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 99/0, heap memory allocated/used/recyclable 2048/144/144, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min 93
Driver 1: standstill, SG min 0
Driver 2: standstill, SG min n/a
Driver 3: standstill, SG min n/a
Driver 4: standstill, SG min n/a
Driver 5: standstill, SG min 0
Driver 6: standstill, SG min 0
Driver 7: standstill, SG min 0
Driver 8: standstill, SG min 0
Driver 9: standstill, SG min 0
Driver 10:
Driver 11:
Date/time: 2022-12-07 12:13:10
Cache data hit count 4004737535
Slowest loop: 22.14ms; fastest: 0.19ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 0.5ms, write time 3.3ms, max retries 0
=== Move ===
DMs created 83, segments created 6, maxWait 14218ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 20, completed 20, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 8], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== Filament sensors ===
Extruder 0 sensor: no data received
=== DueX ===
Read count 1, 0.52 reads/min
=== Network ===
Slowest loop: 15.88ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
= WiFi =
Network state is active
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.26
WiFi MAC address c8:c9:a3:40:01:46
WiFi Vcc 3.42, reset reason Power up
WiFi flash size 2097152, free heap 25912
WiFi IP address 192.168.178.124
WiFi signal strength -57dBm, mode 802.11n, reconnections 0, sleep mode modem
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0
Hi
Thank you for your reply. After M112 I can not really do much more?!? Machine Halted. If I restart the machine and do M98 it sais M98 P "config.g" Warning: Macro file "config.g" not found
Sorry, I'm not a gcode expert by no means.
Hi
Im running a Modix 120Z and even though Modix support has been very helpful they are struggling to figure out this one. I have two issues:
I can run Z-offset, bed tilt and bed levelling and these functions also seem to be working but when I print I seem to have a constant tilt anyway. Front left seems high, complete rear seems low based on first layer test prints. I have since manually shimmed this and get good results but that wasn't the point right.
After running bed leveling I get the following error:
M98 P"0:/macros/Calibration Macros/04_Bed Compensation"
2. Warning: the height map has a substantial Z offset. Suggest use Z-probe to establish Z=0 datum, then re-probe the mesh.
2. 100 points probed, min error -0.329, max error 0.056, mean -0.174, deviation 0.086
2. Height map saved to file 0:/sys/heightmap.csv
I have seen this error being discussed before but non of the posts really come to a conclusion. Any idea's?
