@Phaedrux trying to, but marked as spam

@Phaedrux all i get back is "bad command: ping 192.168.x.x
ok"

Just bought used 3D printer with mods. Trying to understand and connect Duet 3d to wifi. Keep getting the message:
WiFi reported error: Didn’t find access point while trying to connect

Admittedly I know very little about computers, wifi, etc. I've followed the steps on some forums, using serial tools on my mac and have been able to enter my wifi info only to get the flashing blue led and the error message, "WiFi reported error: Didn’t find access point while trying to connect to..."

This is the firmware my machine is running: FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 2.05.1 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2020-02-09b1

Can someone help me please?

Thanks
-Dillon

@Phaedrux Thanks for the response. Was able to clear all saved networks but I get the same message about access points

Any thoughts?

@Phaedrux
M587: Failed to retrieve network list
ok
Error retrieving Wifi status message: bad reply format version
Wifi module is idle
wifi reported error: no known networks found

@Dillon-Brown I may have to call spectrum and get them to direct away from my 5 ghz network again

@Dillon-Brown I then tried M552 S1 and wifi went idle with no known networks found

@Dillon-Brown this is what i get back from M997 S1

M997 S1
Trying to connect at 230400 baud: success
Erasing 4096 bytes…
Erasing 212992 bytes…
Uploading file…
5% complete
10% complete
15% complete
20% complete
25% complete
30% complete
35% complete
40% complete
45% complete
50% complete
55% complete
60% complete
65% complete
70% complete
75% complete
80% complete
85% complete
90% complete
95% complete
Upload successful
ok

@Phaedrux whats the usb terminal? Just the serial tools app ive been using to communicate?

@Dillon-Brown === Platform ===
Last reset 04:02:15 ago, cause: power up
Last software reset time unknown, reason: Heat task stuck, spinning module GCodes, available RAM 11484 bytes (slot 1)
Software reset code 0x00a3 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0043380f BFAR 0xe000ed38 SP 0x200049ac Task 0x4e49414d
Stack: 004486cf 0044a266 01001400 00000000 000004d9 00000000 00000000 3331bb4c 41880000 3e178897 3e1cd04f 3c0281fc 3e3a3325 3e638e29 3e924925 3885108c 397d66d2 c0a00000 00000000 60000010 0043db4f 00000062 0043b3bb
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 19.4, current 33.1, max 33.4
Supply voltage: min 0.0, current 0.4, max 0.6, under voltage events: 0, over voltage events: 0, power good: no
Driver 0: ok, SG min/max not available
Driver 1: ok, SG min/max not available
Driver 2: ok, SG min/max not available
Driver 3: ok, SG min/max not available
Driver 4: ok, SG min/max not available
Date/time: 1970-01-01 00:00:00
Cache data hit count 4294967295
Slowest loop: 200.62ms; fastest: 0.05ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 160, MinFreeDm: 160, MaxWait: 0ms
Bed compensation in use: mesh, comp offset 0.000
=== DDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "M122" in state(s) 0
aux is assembling a command in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 8486.38ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 0 of 8

• WiFi -
  Network state is running
  WiFi module is idle
  Failed messages: pending 0, notready 0, noresp 1
  WiFi firmware version 1.23
  WiFi MAC address 84:0d:8e:b2:15:56
  WiFi Vcc 3.43, reset reason Hardware watchdog
  WiFi flash size 4194304, free heap 23624
  Socket states: 0 0 0 0 0 0 0 0
  === Filament sensors ===
  Extruder 0 sensor: no filament
  ok

@Phaedrux @Phaedrux sure:

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05.1 running on Duet WiFi 1.02 or later
Board ID: 08DGM-956GU-DGMSN-6J1F0-3S06P-KBQMG
Used output buffers: 1 of 24 (1 max)
=== RTOS ===
Static ram: 25712
Dynamic ram: 93216 of which 0 recycled
Exception stack ram used: 304
Never used ram: 11840
Tasks: NETWORK(ready,1244) HEAT(blocked,1232) MAIN(running,3824) IDLE(ready,160)
Owned mutexes:

@Phaedrux trying to, but marked as spam

@Phaedrux
M587: Failed to retrieve network list
ok
Error retrieving Wifi status message: bad reply format version
Wifi module is idle
wifi reported error: no known networks found

@Phaedrux ahh Bummer. Yea i just ran M552 S1 and still get the dreaded M552 S1

@Phaedrux in terminal i got these statistics after the ping command:

38 packets transmitted, 0 packets received, 100.0% packet loss

not sure what that means