Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. Woody78
    • Profile
    • Following 0
    • Followers 0
    • Topics 5
    • Posts 12
    • Best 1
    • Controversial 0
    • Groups 0

    Woody78

    @Woody78

    1
    Reputation
    1
    Profile views
    12
    Posts
    0
    Followers
    0
    Following
    Joined Last Online

    Woody78 Unfollow Follow

    Best posts made by Woody78

    • RE: Problem with Z Driver phase B

      @jay_s_uk okay, thanks thats easy to make.

      posted in Duet Hardware and wiring
      Woody78undefined
      Woody78

    Latest posts made by Woody78

    • RE: RGBW Neopixel on duet 2 wifi

      @droftarts yes i know. i have only the connection problem in my last connector on the hotend...

      posted in Beta Firmware
      Woody78undefined
      Woody78
    • RE: RGBW Neopixel on duet 2 wifi

      @droftarts do you know if i can measure the 3.3v every time or only when the board gives a signal?

      posted in Beta Firmware
      Woody78undefined
      Woody78
    • RE: RGBW Neopixel on duet 2 wifi

      @droftarts okay, i checked another led strip in spare directly on the board without level shifter. it worked fine. so i have to check my wires to the stealthburner, i hope it is no problem that the wires are over 2m long

      posted in Beta Firmware
      Woody78undefined
      Woody78
    • RE: RGBW Neopixel on duet 2 wifi

      @droftarts i´d tried your config with and without level shifter. but nothing happend... i don´t know why...
      it is possible to test the led´s on another way... to check?

      posted in Beta Firmware
      Woody78undefined
      Woody78
    • RGBW Neopixel on duet 2 wifi

      Re: 3.5.0-beta.4 neopixel on duet 2 wifi

      hi there, i have installed my stealthburner with 3 LEDs neopixel 5V version.
      I have also a logic level shifter between board and leds, but nothing happend.
      when i measuring on the pins i have all about 4.95V, i think it is okay...

      in my config.g i have:

      M950 E0 T1 C"connlcd.5" U3
      M150 E0 X3 Q3000000
      M150 E0 R255 P255

      the pins on the board i used are:

      5V = 1)5V CONN_SD
      GND = 2)GND CONN_SD
      3.3V = 5) En10 (LCD_DB7) CONN_LCD

      the 5V and GND goes direct to LEDs and HighInput of LLC and the 3.3V DataLine goes to LowInput LLC

      posted in Beta Firmware
      Woody78undefined
      Woody78
    • RE: Problem with Z Driver phase B

      @jay_s_uk okay, thanks thats easy to make.

      posted in Duet Hardware and wiring
      Woody78undefined
      Woody78
    • Problem with Z Driver phase B

      Hi there,

      i´m using Duet 2 Wifi FW 3.5.3 on my hypercube setup.
      now when i home x axis (i drive first z a little bit down) become a warning: Driver 2 warning: phase B may be disconnected
      the bed doesn´t move and it´s very load on the z steppers, they are shaking...
      few hours ago it´s run normal. then i put the stepper out from the printer, change against other stepper, change back to the old stepper, and everything looks fine. i put the stepper back in the printer, and then works.
      after few hours with power off from the printer, i want to test something, first start G28 X and same again.

      i don´t know what can i do....

      posted in Duet Hardware and wiring
      Woody78undefined
      Woody78
    • RE: create new custom button possible

      @cosmowave thats great. many thanks

      posted in Duet Web Control
      Woody78undefined
      Woody78
    • create new custom button possible

      Hi there, i didn´t find anything to make a own new button in DWC to start for example a macro.
      It is generally possible?

      posted in Duet Web Control
      Woody78undefined
      Woody78
    • RE: Bad command: Configuration file for Duet WiFi

      @chrishamm yes, it is. great. thank you... now everything is fine

      posted in Firmware installation
      Woody78undefined
      Woody78