I've wired up to buttons which will call trigger10.g and trigger11.g
First button is to set the current work XYZ position and the second is to recall/goto the work XYZ position.
How can I achieve this in gcode? I've been using G60 but does not seem to be doing anything.
Workbee CNC.
Board: Duet 2 WiFi (2WiFi)
Firmware: RepRapFirmware for Duet 2 WiFi/Ethernet 3.5.3 (2024-09-18)
Duet WiFi Server Version: 2.1.0
System Settings Version: 1.2
@droftarts Thank you!
Earlier today I replaced the WIFI Module with the Ethernet module from a faulty board I had years ago (drivers died, I kept the board for spares). (Save make/version etc).
The Ethernet module was recognized, I can set the IP etc. Sadly, It's still showing "Link Down" with the Ethernet cable connected.
I can only assume at this point one of the traces are damaged on the PCB and the signal is not making it back to the atmel chip.
I do have a full re-flow station and microscope. Just not sure if its worth the dive vs go just buy a new one.
This is a Workbee CNC, purchased from a private seller. The unit was working following an upgrade directly from workbee then reboot and all is dead.
@jay_s_uk said in Unable to start WIFI Module:
M552 S0
M552 S0
ok
M997 S1
Trying to connect at 230400 baud: failed
Trying to connect at 115200 baud: failed
Trying to connect at 74880 baud: failed
Trying to connect at 9600 baud: failed
Error: Installation failed due to comm write error
ok
M997 S0
Shutting down USB interface to update main firmware. Try reconnecting after 30 seconds.
This did not fix the issue.
Following the upgrade tutorial from Ooznest firmware update. The WIFI Module has stopped working.
Duet 2 Wifi (PCB Version 1.04c)
Wifi Module ESP 07S
It claims to be "starting" but never does.
M115
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.3 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2021-06-15 21:45:03
ok
M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.3 (2021-06-15 21:44:54) running on Duet WiFi 1.02 or later
Board ID: 0JD0M-9P6B2-NJ4S8-6JKF4-3SN6L-9U4AK
Used output buffers: 1 of 24 (12 max)
=== RTOS ===
Static ram: 23876
Dynamic ram: 74172 of which 176 recycled
Never used RAM 13336, free system stack 185 words
Tasks: NETWORK(ready,8.0%,517) HEAT(delaying,0.0%,386) Move(notifyWait,0.1%,364) MAIN(running,91.9%,431) IDLE(ready,0.0%,29), total 100.0%
Owned mutexes: USB(MAIN)
=== Platform ===
Last reset 00:07:57 ago, cause: software
Last software reset at 2025-01-07 13:23, reason: User, GCodes spinning, available RAM 13512, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Step timer max interval 0
MCU temperature: min 29.7, current 30.2, max 30.4
Supply voltage: min 0.5, current 0.5, max 0.6, under voltage events: 0, over voltage events: 0, power good: no
Heap OK, handles allocated/used 99/1, heap memory allocated/used/recyclable 2048/24/0, gc cycles 0
Driver 0: position 0, ok, SG min/max not available
Driver 1: position 0, ok, SG min/max not available
Driver 2: position 0, ok, SG min/max not available
Driver 3: position 0, ok, SG min/max not available
Driver 4: position 0, ok, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 1970-01-01 00:00:00
Cache data hit count 4294967295
Slowest loop: 6.90ms; fastest: 0.13ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.1ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is ready with "M122" in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 0.18ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 0 of 8
- WiFi -
Network state is starting2
WiFi module is disabled
Failed messages: pending 0, notready 0, noresp 1
Socket states: 0 0 0 0 0 0 0 0
ok