ya no se que hacer alguna ayuda por favor?
modelo de motor nema17HS4023

M122
=== Diagnostics ===
Used output buffers: 3 of 32 (6 max)
=== Platform ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 1.21RC3 running on Duet Ethernet 1.02 or later
Board ID: 08DGM-95BLL-N6PSS-6J9F2-3SN6M-1JUZJ
Static ram used: 16144
Dynamic ram used: 100056
Recycled dynamic ram: 2584
Stack ram used: 1224 current, 4496 maximum
Never used ram: 7792
Last reset 00:07:29 ago, cause: software
Last software reset at 2018-06-05 14:16, reason: User, spinning module GCodes, available RAM 7856 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000, CFSR 0x00000000, ICSR 0x0441f000, BFAR 0xe000ed38, SP 0xffffffff
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms
MCU temperature: min 37.5, current 37.6, max 39.2
Supply voltage: min 12.2, current 12.3, max 12.4, under voltage events: 0, over voltage events: 0
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2018-06-05 14:23:55
Slowest main loop (seconds): 0.004703; fastest: 0.000052
=== Move ===
MaxReps: 0, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm 240, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Responder states: HTTP(1) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
=== Network ===
State: 5
HTTP sessions: 1 of 8
=== Expansion ===

Hello
I still have problems of excess temperature in the engines even Having passed the firm of the duet to the previous one that I had (1.21 RC3) that did not give me problems with the temperature of the engines I can not do any part since the extruder motor jumps and I stopped printing when I stopped printing the temperature of the engines low and stayed at room temperature only heated when it is printing and I do not know why I need help please this problem I did not expect it and I'm desperate I do not know what to do.
Now I have the amperage of the 800mA motors as I had them since I mounted the Duet3d board but I have also tried to lower mA and keep doing it until the engines stop working

@carlosspr
M913

Motor current % of normal - X:100, Y:100, Z:100, E100100100100:100

@dc42
Hi, thanks for your attention
I have an ethernet duet in a creality CR-10 has a nema 17 and they end up heating up a lot when I make an impression until the extruder motor loses steps and stops extruating at that moment the Y and X motors along with the extruder are very very hot happens to me since I upgrade to 1.21 since before with the 1.21 RC3 had no problem
When I send an M906 it puts me this:

× M906

Motor current (mA) - X: 800, Y: 800, Z: 800, E: 800: 800: 800: 800: 800: 800: 800: 800: 800, inactive factor 30%

and M916 gives me this error:
M916

Error: M916: Resume prologue file 'resurrect-prologue.g' not found

Hola buenas
since a week ago I have problems of overheating in my Cartesian printer with duet ethernet of my engines I have them at 800mA and before updating to 1.21 I did not have these problems as I could solve it? I want to go back to 1.21Rc3 that with this version I did not have these problems
what would be the procedure to go from 1.21 to the previous version 1.21RC3 on my ethernet board