@phaedrux OK, M98 was quite helpful as well as resolving the unlabeled "D". I can now see both thermistors! Thank you!
The next thing I need to resolve is converting from the legacy splitting the dual Z axis into Z & U, to the new process. I think I understand it but we'll see.
Thanks again!
@phaedrux Sorry for the delay.
I bought a new one, and the same thing happened. Went white after the erase/reset, and was not detected on my PC. So instead, I tried the method of updating vies the Duet even though the PanelDue FW was not 3.2.2 as per the instructions for this method. It was 1.24. But it worked fine!
Then I went back and tried that method on the old PanelDue, and that also worked!
So I'm all set! Thanks for all your help!
@phaedrux At this point I have tried 3 computers, 10 USB ports, and 4 USB cables (that all work with other items). And nothing works
I've tried the erase and reset steps many times at this point. And the PC is still not seeing it as a USB device. My PC is on Win 11 Pro.
I have used Bossa successfully in the past to update the PanelDue's FW, but it has been several years.
@phaedrux Yes they are equal, and homing all axis works fine - Thanks for your help!
After going through the upgrading FW from 1.02 progressively to 3.4.1 for my Duet 2 Wifi, I went to update the FW for the PanelDue 7i. I turned everything off on my printer, disconnected the PanelDue. Connected to via USB to my PC, hit the Erase button followed by the Reset button, and the screen went basically white. Neither my PC nor Bussa will "see" it connected. No indication that a new USB device is connected. Does not show in device manager. I have tried my PC, my MacBook, and 5 USB cables with the same result. I need to update the PanelDue FW via USB since the current FW is too old.
Also, my printer requires the PanelDue to be connected in order to boot up, even though the screen is still black.
Any suggestions? Thanks!
@phaedrux Simpler than I thought. And No probe.
And yes driver 2 is zstop, and driver 3 is eostop.
Thanks again!
@phaedrux
This is how they are actually wired: I have Z steppers on Drivers 2 (Z) and 3 (E0), and endstops: zstop and e0stop.
@dc42 Hi DC42!
I have 2 end stop switches, one for each motor. What do I need to change?
Thanks!
Trying to comply with setup of Dual Z steppers and endstop after upgrading from 1.02 FW progressively to 3.4.1 FW on a Duet 2 Wifi. I had this working on the old FW by splitting Z into Z and U, but I see that is no longer required in the current FW. (Note X and Y axis run fine, have not tested Z yet due to the errors below)
I have Z steppers on Drives 2 (Z) and 3 (E0), and endstops zstop and e0stop.
I assume I am missing something, any help certainly appreciated!
Running M98 P"coonfig.g" results are:
M98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Error: Pin 'zstop' is not free
Error: Invalid Z probe index
My config.g:
; Configuration file for Duet WiFi (firmware version 1.21) UPDATED by WMM for Dual Z Motors and End Stops
; executed by the firmware on start-up
; NEW Indicated for lines edited to support dual Z=Stops
; generated by RepRapFirmware Configuration Tool v2 on Tue Dec 18 2018 16:44:11 GMT-0500 (Eastern Standard Time)
; Upgraded to FW v3.4.1 7/24/2022
; General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
M669 K1 ; New 3 Select CoreXY mode K1
; Network
M550 P"" ; Set machine name
M551 P"" ; Set password
M552 S1 ; Enable network
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet
; Drives
M569 P0 S0 ; Drive 0 goes BACKWARDS Y Homes to the FRONT X Homes to the LEFT
M569 P1 S1 ; Drive 1 goes forwards Y Homes to the FRONT X Homes to the LEFT
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S1 ; Drive 3 goes forwards
M569 P4 S1 ; Drive 4 goes forwards
M584 X0 Y1 Z2:3 E4 P3 ; New V3 2 steppers for Z
M350 X16 Y16 Z16 E16 I1 ; NEW V3 Configure microstepping without interpolation Changed E to 16
M92 X80.00 Y80.00 Z400.00 E476.5 ; NEW V3 Set steps per mm With the change in microstepping above, all stepps/mm needed to be cut in half except E for some reason
M566 X100.00 Y100.00 Z12.00 E20.00 ; NEW V3 Set maximum instantaneous speed changes (mm/min) JERK NEW Added U was 900 for X/Y
M203 X3600.00 Y3600.00 Z600.00 E2400.00 ; NEW V3 Set maximum speeds (mm/min) NEW Added U Changed Max Speed for Z/U to 600 was 6000
M201 X800.00 Y800.00 Z20.00 E500.00 ; NEW V3 Set accelerations (mm/s^2) NEW Added U - changed X+Y to 1500 from 3000
M906 X1000.00 Y1000.00 Z1400.00 E800.00 I30 ; NEW V3 Set motor currents (mA) and motor idle factor in per cent NEW Added U
M84 S30 ; Set idle timeout
; Axis Limits NEW Added
M208 X1 Y0 Z0 S1 ; Set axis minima NEW added U0 was all 1
M208 X400 Y370 Z380 S0 ; Set axis maxima NEW Revised max from X390 Y390
; Endstops
M574 Z1 P"nil" ; In theory frees up zstop from preassigned
M574 X1 S1 P"xstop" ; New for ver 3 Note if using Stallgaurd less info is required All
M574 Y1 S1 P"ystop" ; New for ver 3
M574 Z1 S1 P"zstop+e0stop" ; New for ver 3
; Z-Probe
;M558 P5 X0 Y0 Z0 H2 F60 T6000 ; Set Z probe type to switch, the axes for which it is used and the dive height + speeds, edited P0 to P4 indicating switch
M558 P5 C"zstop+e0stop" H2 F60 T6000 ; New V3
G31 P600 X0 Y0 Z0 ; Set Z probe trigger value, offset and trigger height
M557 X20:360 Y20:360 S20 ; Define mesh grid
; HEATERS
; Bed
M308 S0 P"bedtemp" Y"thermistor" T100000 B3950 R4700 ; New 3 Bed Keenovo
M950 H0 C"bedheat" T0 ; New 3
;M307 H0 B0 S1.00 ; Disable bang-bang mode for the bed heater and set PWM limit
M307 H0 A90.0 C700.0 D10.0 S1.00 V0.0 B0 ; Copied from override file
M140 H0 ;
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
; Hotend
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 C7.060000e-8 ; New 3
M950 H1 C"e0heat" T1 ; New 3
M307 H1 A232.6 C90.5 D0.9 S0.50 V12.1 B0 ; Copied from override file
M143 H1 S300 ; Set temperature limit for heater 1 to 300C; Before Revo was 280
; Fans
M950 F0 C"fan0" Q500 ; New 3
M106 P0 S0 H-1 ; Revised V3 Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off Changed from S0.3
M950 F1 C"fan1" Q500 ; New 3
M106 P1 S1 H-1 ; New 3
; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
; PanelDue
M575 P1 B57600 S1 ; New V3 PanelDue specific
; Automatic saving after power loss is not enabled
; Custom settings are not configured
; Miscellaneous
T0 ; Select first tool
;M501 ; Load latest PID Tune for H1