It is still not working, I changed the rep rap config files. Made an entirely new with 3.0 firmware version and CoreXY geometry for the Modix Big-60 printer.

This configuration file is forwarded by the printer company. I guess they had worked this through with Duet, I am assuming this here.

I will give this a try and change it to core XY and will let you know soon.

Will changing the limit of X to 1200mm work, I tried it does cover the whole bed but this might affect my 3d prints and their Gcodes.

Please suggest a fix.

I tried changing steps to the following values:

40, 60, 80, 120 but nothing worked for X-axis. In the end, it just disturbed my other axes movements too.

Here are the screenshots.

tpre0.g tpost0.g tfree0.g stop.g sleep.g retractprobe.g resurrect-prologue.g resume.g rehome.g pause.g homez.g homey.g homex.g homeall.g deployprobe.g config.json config.g cancel.g bed.g Yes, it was 100 steps per mm previously. Even now after version change. But it never traveled 600mm on X-axis. I tried switching the X and Y motors connections. But then, both axes X and Y then travel half the distance (i.e 300 mm instead of 600mm).

My printer build size is 600mm x 600mm x 600mm, it is MODIX Big60.

I already calculated with the formula but the problem is there are different GT2 pulleys with different teeth no.s, for an instance, in X-axis NEMA23 has a mounted GT2 16 teeth pulley driving a GT2 40 teeth (double width) pulley which further is coaxial with a GT2 20 teeth pulley driving the belt of the X-axis.

Y-axis uses a GT2 16 teeth to GT2 20 teeth to drive a belt.

I am attaching the config.g file and homing files. [0_1589565222694_Big60-Configuration (1).zip](Uploading 100%)

Also a screenshot of calculations.

Here is the image for reference I had set X max 600mm & Y max 600, printer as Cartesian. All axes move in right manner except X-axis as only this move half of the printer distance than other axes. I manually move this to 600mm using dashboard but it actually moves only 300mm. Please suggest changes.

I have changed the Firmware version to 3.0 as I am working on it now.

My x-axis movement is weird here. The limit of the X-axis is 600mm but when I Home the axis and then move the x-axis, it moves weirdly. It moves 5mm when given a command to move 10mm and also it never reaches the limit as 600mm is reached in the middle of the printer.

The zero of x or home of the x-axis is located at the top left corner of the printer.

Please suggest a solution.

I already downloaded the firmware files named Duet2CombinedFirmware.bin and then I deleted the existing file in the SD card. Then, I copy and paste the new firmware file mentioned above in the sys folder. Basically, I followed the link here. I can see the firmware version of my board when I connect to YAT but still, my PANELdue 7i LCD is not working.
The above pictures are the pictures taken after following the fallback procedure#3.

The link I used: https://duet3d.dozuki.com/Wiki/Installing_and_Updating_Firmware

Do you want me to retry the Fallback procedure#3? I already tried it once but no success.

Hi,

I got my Duet 2 Wifi board and the PANELDue 7i LCD few weeks ago. I opened my package 2 days ago. Then, I followed the getting started guide. I upgraded the firmware to 3.0. Reinserted my SD card into my Duet 2 wifi board and then followed Duet Web control setup. Then to check my PANELDue 7i LCD i made the wired connection as shown with USB and also tried with a small 12v 1.3A battery but none of these worked as my LCD backlight do turn as you in photos but nothing shows up on my PANELDue 7i LCD.

Also, my duet board sometimes disconnects randomly. I checked on YAT it is still showing firmware. Please suggest a solution or i like to get an exchange for Duet 2 wifi and PANELDue 7i board which what I have right is not intact or damaged.
l