@Phaedrux well the largest file i could complete is right around the 1mb mark. Anything larger fails. the file progress progresses to about 35% and resets to 0 a few times before failing... I also tried uploading by ftp i can delete files on the duet from ftp but as soon as i initiate the upload it fails no matter the file size. Im logged in as anon so that could be it.

As for smaller files it takes around a minute to upload but they do succeed thru !DWC!

As for navigation. DWC seems sluggish and I can only connect to it from 1 computer at a time.

Oh once i get the gcode to the SD (as in copying it from my computer with an sd adapter). It prints beautifully.

Signal stays constant. Ive also tried changing the wifi channel, alas no dice.

Hello. After a few days of configuring and settin my Duet WiFi board. The only issue I'm having is not being able to upload my gcodes because of timeouts. Transfers start out great then drops speed into the kbps, then timeout. Here is my M122 report. Also, Ive changed my SD card to a different one. (both off brand, bought a brand name one off amazon. should be here in a couple days just to be sure) I've also re flashed this device just to make sure as well. Thanks again for this really well made board!

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet WiFi 1.02 or later
Board ID: 08DLM-996AL-K65SN-6JTDJ-3SD6N-992UY
Used output buffers: 3 of 24 (13 max)
=== RTOS ===
Static ram: 27980
Dynamic ram: 93840 of which 44 recycled
Exception stack ram used: 560
Never used ram: 8648
Tasks: NETWORK(ready,384) HEAT(blocked,1224) MAIN(running,1848) IDLE(ready,80)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:33:17 ago, cause: software
Last software reset at 2020-08-03 23:45, reason: User, spinning module GCodes, available RAM 9144 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 32.5, current 33.5, max 35.7
Supply voltage: min 24.1, current 24.3, max 24.7, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max 21/214
Driver 1: ok, SG min/max 0/187
Driver 2: ok, SG min/max 0/183
Driver 3: ok, SG min/max 0/123
Driver 4: standstill, SG min/max not available
Date/time: 2020-08-04 00:18:23
Cache data hit count 3329487922
Slowest loop: 48.84ms; fastest: 0.12ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 2.8ms, write time 1.9ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 166, MinFreeDm: 144, MaxWait: 54149ms
Bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 3010, completed moves: 3006, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: 3
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.5
=== GCodes ===
Segments left: 1
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is doing "G1 X-48.479 Y-29.807 E0.00872" in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 42.10ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- WiFi -
Network state is active
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address 50:02:91:6a:34:21
WiFi Vcc 3.35, reset reason Unknown
WiFi flash size 4194304, free heap 24072
WiFi IP address 192.168.1.181
WiFi signal strength -38dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0