dc42 Thank you for your response.
The DWC was showing 1000 in the Z probe.
After reading more about M558 I changed the I parameter from I0 to I1 in the config.g file and that solved the problem.
So a big thank you dc42 very helpful.
Best posts made by buetuser
-
RE: G30 code does not execute
Latest posts made by buetuser
-
RE: Printing stops after a few hours
Thank you for responding. I have now upgraded to 2.02 release and I will order a new SD card. I hope this solves the problem.
Is there a particular SD card that is recommended for use with the Duet 2?
Thank you for any advice. -
RE: Printing stops after a few hours
Hi
Sorry for not including this info in the first post.
My printer is a diy corexy the controller is Duet 2 EthernetFirmware Name: RepRapFirmware for Duet 2 WiFi/Ethernet
Firmware Electronics: Duet Ethernet 1.02 or later
Firmware Version: 2.02RC1(RTOS) (2018-08-31b4)
Web Interface Version: 1.22.3
My config 0_1550956108785_config.g
I have checked and read all the posts I could find on this subject but I could not find any answers.
Thanks -
Printing stops after a few hours
Hi
I was printing a file and my printer stopped part way through and showed the fault :-Error: Cannot read file, error code 1.
Cancelled printing file ShortABS_Lion_Head.gcode, print time was 3h 22mThis is the second time it has stopped after printing for a few hours, this is with 2 different files and the time was not exactly the same but perhaps about 3 hours the first time and as you can see 3h 22m the second time.
What does error code 1 mean and what are some reasons why it would just stop reading the file.
Thanks for any help. -
RE: G30 code does not execute
dc42 Thank you for your response.
The DWC was showing 1000 in the Z probe.
After reading more about M558 I changed the I parameter from I0 to I1 in the config.g file and that solved the problem.
So a big thank you dc42 very helpful. -
G30 code does not execute
Hi
I have a diy corexy printer, which was working perfectly with my Duet Ethernet.
I updated to a Precision Piezo probe to do away with the Z home micro switch. The problem is that G30 code does not work. This is the home all gcode.; homeall.g
G91
G1 S1 Z5 F6000
G1 S1 X-305 Y-305 F1800
G1 S1 X-305
G1 S1 Y-305
G1 X5 Y5 F6000
G1 S1 X-305 F360
G1 S1 Y-305
G90
G1 Y150 X150 F6000
G30G1 Z5
G1 Y0 X0 F6000
G1 Z0.05When I execute this everything operates as it should X and Y home and then move to the center of my bed, ie: G1 Y150 X150 F6000 then it just ignores the G30 probe code and executes the rest of the code moving the head back to Y0 and X0.
Why is it not probing the bed with G30?
I have searched the forum for answers but I can’t find anything relating to this problem.Thanks in advance for any help you can give.
-
RE: Confirmation of a board purchase
Hi.
I have there has been no email from Duet3d. I have just registered for this site and I have received a confirmation email in order to post on here, so I know my email is working fine. -
Confirmation of a board purchase
I have just purchased a new Duet board but I have not received confirmation of the purchase. Is this usual for Duet3d? I have received confirmation that I have paid for it from Paypal.