Hey, so I've just swapped to the BLTouch and I have some issues after setting it up
My mesh looks like this
and I don't why
here is my config.g:
; General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
; Drives
M569 P0 S0 ; Physical drive 0 goes forwards
M569 P1 S0 ; Physical drive 1 goes forwards
M569 P2 S1 ; Physical drive 2 goes backwards
M569 P3 S0 ; Physical drive 3 goes forwards
M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
M92 X100.00 Y100.00 Z400.00 E90.00 ; Set steps per mm
M566 X600.00 Y600.00 Z18.00 E300.00 ; Set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E6000.00 ; Set maximum speeds (mm/min)
M201 X1500.00 Y1500.00 Z100.00 E10000.00 ; Set accelerations (mm/s^2)
M906 X500.00 Y500.00 Z500.00 E800.00 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 X-48.90 Y-3.00 Z0 S1 ; Set axis minima
M208 X220 Y220 Z240 S0 ; Set axis maxima
; Endstops
M574 X1 Y1 S0 ; Set active low and disabled endstops
; Z-Probe
M307 H3 A-1 C-1 D-1 ; Set Z probe trigger value, offset and trigger height
M558 P9 H5 F100 T2000
G31 X-21 Y-54 Z1.023 P25
; Heaters
M307 H0 B0 S1 ; Disable bang-bang mode for the bed heater and set PWM limit
M305 P0 T100000 B4725 C7.060000e-8 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S80 ; Set temperature limit for heater 0 to 80C
M307 H0 A187.0, C617.0, D8.1 S1 ; PID Bed - 5 way Diamond
M305 P1 T100000 B3950 C7.060000e-8 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S250 ; Set temperature limit for heater 1 to 250C
M307 A599.9 C121.3 D4.5 S1 ; PID Heater 5 way Diamond
; Fans
M106 P0 S0.6 I0 H1 T120 X0.7 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P1 S1.0 I0 H1 T45 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
; Tools
M563 P0 H1 D0 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
; Automatic power saving
M911 S22 R23 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss
; Custom settings are not configured
; Miscellaneous
T0 ; Select first tool
Here is my bed.g:
M401
G29 ; probe the bed and enable compensation
G29 S1
Could it be a physical problem? I printed my own mount