Posts made by eznish

@eznish
Yes. I found this document and follow this instruction.

@dc42 Thanks a lot!
Unfortunately I dont know how to use 74LVC06A chip . Maybe I should change motor witout external stepper driver.
Thanks again!

Hello all
I have problem on duet3 mini5 wifi and nema 23 motor.
I am trying to use Duet mini5 with IHSS57-36-20 Stepper motor which is integrated with stepper driver.

What I know is duet mini 5+ has external stepper drive pin so I connects Pins to IHSS57-36-20 Stepper motor's connector.

Like this
Left red letter is on duet board -> Motor driver connector.

1. V_fused
   2. GND: Step- →PUL-
2. D5-Diag
   4. D5_Step: Step+ → PUL+
   5. D5_DIR: DIR+
   6. +3.3V: Enable+
   7. GND: DIR-
3. V_Fused
4. GND :
5. S_uart_B
6. D6_Diag
7. D6_Step :
8. D6_DIR:
9. 5V_INT
10. GND :
    16. Driver_EN: ENable -

** I tried to use 5V(no.9) instead of 3.3V already.

I set this motor as Drive 5. in configuration In "My duet" Browser. But Motor is not working. here is my configuration.

Configuration----------------------------------------------------------------
; Configuration file for Duet 3 Mini 5+ (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.15 on Tue Dec 13 2022 01:00:50 GMT+0900 (한국 표준시)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"My Printer" ; set printer name
M665 R105.6 L215 B85 H250 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0 ; put your endstop adjustments here, or let auto calibration find them

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0.0 S1 ; physical drive 0.0 goes forwards
M569 P0.1 S1 ; physical drive 0.1 goes forwards
M569 P0.2 S1 ; physical drive 0.2 goes forwards
M569 P0.5 S1 ; physical drive 0.5 goes forwards
M584 X0.0 Y0.1 Z0.2 E0.5 ; set drive mapping
M350 E1 I0 ; configure microstepping without interpolation
M350 X16 Y16 Z16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z80.00 E80.00 ; set steps per mm
M566 X1200.00 Y1200.00 Z1200.00 E1200.00 ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z18000.00 E18000.00 ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z1000.00 E1000.00 ; set accelerations (mm/s^2)
M906 X1000 Y1000 Z1000 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 Z0 S1 ; set minimum Z

; Endstops
; WARNING: No endstops configured

; Z-Probe
M558 P0 H5 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed
M557 R85 S20 ; define mesh grid

; Heaters
M140 H-1 ; disable heated bed (overrides default heater mapping)

; Fans

; Tools

; Custom settings are not defined

---

Motor is making little sounds when it is in idle mode and when I set extruding(I set this motor on E). idle sound change very little. ( I thought i did wiring right way)

Can you give me some advice to make this motor work?
I am thinking it may be because of Steps per mm (in configuration setting). But i am not sure. I spend many days to fix this problem but now I am lost.

** Info

1. Power
   I am using smps 24V output.
2. Motor
   <JMC Original Nema 23 2Nm DC36V>
   24~50VDC
   4.5A 20khz pwm
   Pulse max: 200k

Thanks