@dc42 Thx, that fixed my problem. Any idea what could be the cause of this? Many thx.

Thanks for the suggestion but no luck 60 seconds till the file loads.

Hi,

Since a week the webinterface of the Duet2 Wifi board loads very slow:

The dwc.js file takes 25 seconds to load.

Also sending movement commands seem to be slow:

I've replaced the SD card with a another one and sadly the same result.

Also the status update sometimes seem to take 2 seconds:

I've updated the firmware to the latest version:

Here's the output of the M112 command:
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.02(RTOS) running on Duet WiFi 1.02 or later
Board ID: 08DGM-917NK-F2MS4-7JKD6-3SN6P-9GUNG
Used output buffers: 1 of 20 (8 max)
=== RTOS ===
Static ram: 25524
Dynamic ram: 98524 of which 0 recycled
Exception stack ram used: 280
Never used ram: 6744
Tasks: NETWORK(ready,648) HEAT(blocked,1232) MAIN(running,3812) IDLE(ready,200)
Owned mutexes:
=== Platform ===
Last reset 00:01:42 ago, cause: software
Last software reset at 2019-01-26 19:55, reason: User, spinning module GCodes, available RAM 6744 bytes (slot 2)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 28.8, current 29.3, max 29.5
Supply voltage: min 19.3, current 19.4, max 19.5, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2019-01-26 19:57:19
Cache data hit count 376775670
Slowest loop: 2.47ms; fastest: 0.07ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0
=== Move ===
Hiccups: 0, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm: 240, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 22.73ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8

• WiFi -
  Network state is running
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.22
  WiFi MAC address b4:e6:2d:53:15:de
  WiFi Vcc 3.46, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 27552
  WiFi IP address 192.168.11.179
  WiFi signal strength -53dBm, reconnections 0, sleep mode modem
  Socket states: 0 0 0 0 0 0 0 0

When I upload a file I get a speed of 350 KiB/s.

Any help would be welcome!

Kind regards,
Frederik