Posts made by Gluedl

Hi all,

thank you so much for your support, especially Ian!

I bought the Duet from Filafarm.de, I will contact them later today.

Here is the picture of the processor with it's sticker:

.

I absolutely dont mind that you use the pictures, I will send you the best 2 original ones in full size for further use.

I will keep you updated on the build process of my printer.

Have a nice day

Mike

Tried that, does not work unfortunately...

Good evening everybody, many thanks so far!

Here are some pics:

And the results from the YAT console with both cards:

m21
M21: Cannot initialise SD card 0: Card is unusable
ok

m39
M39: No SD card mounted in slot 0
ok

m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.03 running on Duet WiFi 1.02 or later
Board ID: 08DJM-9178L-L4MSN-6JTD8-3S86Q-K80QN
Used output buffers: 1 of 24 (12 max)
=== RTOS ===
Static ram: 25680
Dynamic ram: 93208 of which 0 recycled
Exception stack ram used: 308
Never used ram: 11876
Tasks: NETWORK(ready,1416) HEAT(blocked,1236) MAIN(running,3828) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 00:11:31 ago, cause: power up
Last software reset time unknown, reason: Heat task stuck, spinning module GCodes, available RAM 11524 bytes (slot 2)
Software reset code 0x00a3 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0443380f BFAR 0xe000ed38 SP 0x2000499c Task 0x4e49414d
Stack: 0043aa9b 00446aae 01000000 00000000 00000000 3edb6db7 b7b4d800 3331bb4c 40000000 3f317200 b5ddea0e 388aa908 bb35fe81 3c4192f5 00000000 00000000 00000000 00000000 00000000 60000010 0044cbc7 0000004a 0043aa9b
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 12.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 30.2, current 32.1, max 32.5
Supply voltage: min 13.9, current 14.0, max 14.1, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 1970-01-01 00:00:00
Cache data hit count 2657472349
Slowest loop: 261.77ms; fastest: 0.08ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 0 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "m122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 201.14ms; fastest: 0.08ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 0 of 8

• WiFi -
  Network state is running
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 2
  WiFi firmware version 1.23
  WiFi MAC address 84:0d:8e:b2:f4:6f
  WiFi Vcc 3.40, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 26016
  WiFi IP address xxxxxxxxxxx
  WiFi signal strength -58dBm, reconnections 0, sleep mode modem
  Socket states: 0 0 0 0 0 0 0 0
  ok

M552 S1
ok
WiFi module started
WiFi module is connected to access point FRITZ!Box 7412, IP address xxxxxxxxxxxxxx
m21
m39
M21: Cannot initialise SD card 0: Card is unusable
ok
M39: No SD card mounted in slot 0
ok
m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.03 running on Duet WiFi 1.02 or later
Board ID: 08DJM-9178L-L4MSN-6JTD8-3S86Q-K80QN
Used output buffers: 1 of 24 (1 max)
=== RTOS ===
Static ram: 25680
Dynamic ram: 93208 of which 0 recycled
Exception stack ram used: 308
Never used ram: 11876
Tasks: NETWORK(ready,1416) HEAT(blocked,1236) MAIN(running,4500) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 00:00:52 ago, cause: reset button or watchdog
Last software reset time unknown, reason: Heat task stuck, spinning module GCodes, available RAM 11524 bytes (slot 2)
Software reset code 0x00a3 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0443380f BFAR 0xe000ed38 SP 0x2000499c Task 0x4e49414d
Stack: 0043aa9b 00446aae 01000000 00000000 00000000 3edb6db7 b7b4d800 3331bb4c 40000000 3f317200 b5ddea0e 388aa908 bb35fe81 3c4192f5 00000000 00000000 00000000 00000000 00000000 60000010 0044cbc7 0000004a 0043aa9b
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 12.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 31.6, current 32.2, max 32.5
Supply voltage: min 13.9, current 14.0, max 14.0, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 1970-01-01 00:00:00
Cache data hit count 127602054
Slowest loop: 112.07ms; fastest: 0.08ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 0 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "m122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.43ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 0 of 8

• WiFi -
  Network state is running
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.23
  WiFi MAC address 84:0d:8e:b2:f4:6f
  WiFi Vcc 3.40, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 26104
  WiFi IP address xxxxxxxxxx
  WiFi signal strength -56dBm, reconnections 0, sleep mode modem
  Socket states: 0 0 0 0 0 0 0 0
  ok

None of the 2 cards work, both cards have the same interface speed: 12.0MBytes/sec.

Any further help would be greatly appreciated.

I think I am good on the SD card formatting as I followed the steps mentioned here: https://duet3d.dozuki.com/Wiki/SD_Card

I will try again tonight with the structure you recommend

As for the soldering of the card tray, I had a good look at it and it "seemed fine", I will upload a photo from home tonight.

This forum is awesome, reply times a really fast. THANKS GUYS!!!

I downloaded the files from here:

https://github.com/T3P3/Duet/blob/master/Duet2/SD Card Contents/SD_Card_Contents.zip

The original structure was identical to the one I downloaded:

folder gcodes
folder macros
folder sys
folder www
Duet driver files (archive)

I am at work now and cannot upload pictures and create links for them...

Hello all,

my name is Mike, 42 year old electrical engineer from Luxembourg and I am in the process a building a big (1cubic meter) 3D Printer. I wanted to go with the Duet Wifi 2 board, but I am getting quite frustrated atm, because I cannot get the SD card working on the one i bought a few weeks ago. I have tested the one delivered with the board, formatted it to FAT32 with the original software, got the SD card files fresh from the net and repeated all the steps with a brand new card. The result is always the same:

I cannot connect to the Duet website: it says I should control if the www folder contains all the files...
I cannot update the firmware via SD...

Both SD cards are 8GB variants, both get recognized by my PC.

And here is what I get out from the board with YAT:

M21
M21: Cannot initialise SD card 0: Card is unusable
ok
m39
M39: No SD card mounted in slot 0
ok
m39
M39: No SD card mounted in slot 0
ok
m39
M39: No SD card mounted in slot 0
ok
m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.03 running on Duet WiFi 1.02 or later
Board ID: 08DJM-9178L-L4MSN-6JTD8-3S86Q-K80QN
Used output buffers: 1 of 24 (2 max)
=== RTOS ===
Static ram: 25680
Dynamic ram: 93208 of which 0 recycled
Exception stack ram used: 308
Never used ram: 11876
Tasks: NETWORK(ready,1116) HEAT(blocked,1236) MAIN(running,4500) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 00:03:04 ago, cause: reset button or watchdog
Last software reset time unknown, reason: Heat task stuck, spinning module GCodes, available RAM 11524 bytes (slot 2)
Software reset code 0x00a3 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0443380f BFAR 0xe000ed38 SP 0x2000499c Task 0x4e49414d
Stack: 0043aa9b 00446aae 01000000 00000000 00000000 3edb6db7 b7b4d800 3331bb4c 40000000 3f317200 b5ddea0e 388aa908 bb35fe81 3c4192f5 00000000 00000000 00000000 00000000 00000000 60000010 0044cbc7 0000004a 0043aa9b
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 12.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 25.5, current 28.3, max 28.5
Supply voltage: min 0.0, current 14.0, max 14.1, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 1970-01-01 00:00:00
Cache data hit count 604633099
Slowest loop: 111.95ms; fastest: 0.06ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 0 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "m122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.40ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 0 of 8

• WiFi -
  Network state is running
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.23
  WiFi MAC address 84:0d:8e:b2:f4:6f
  WiFi Vcc 3.40, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 26184
  WiFi IP address xxxxxxxxxxxxxxx
  WiFi signal strength -66dBm, reconnections 0, sleep mode modem
  Socket states: 0 0 0 0 0 0 0 0
  ok
  M21
  M21: Cannot initialise SD card 0: Card is unusable
  ok

I tried powering the board solely over USB, solely over a 13.6V power supply and with both combined, the cards never worked.

Have I missed some steps or is there something wrong with my board?

Thanks in advance for your feedback.

Mike