Posts made by hobdayd

Many thanks. The issue was I was using Pronterface which was as you said sending capital letters. Changed to YAT and worked fine.

I could not have done this without your help.

Many Thanks once again.

Ok thanks. I will try it tomorrow and report back.

Ok, sorry for asking basic questions...I have got this far but still having issues...

Printer is now online.

M997 S0:1
SENDING:M997 S0:1
Trying to connect at 460800 baud:
success
Erasing 296832 bytes...
Uploading file...
5% complete
10% complete
15% complete
20% complete
25% complete
30% complete
35% complete
40% complete
45% complete
50% complete
55% complete
60% complete
65% complete
70% complete
75% complete
80% complete
85% complete
90% complete
95% complete
Upload successful
[ERROR] Can't read from printer (disconnected?) (SerialException): call to ClearCommError failed
[ERROR] Can't write to printer (disconnected?) (SerialException): WriteFile failed ([Error 22] The device does not recognize the command.)
[ERROR] Can't write to printer (disconnected?) (SerialException): WriteFile failed ([Error 22] The device does not recognize the command.)
[ERROR] Can't write to printer (disconnected?) (SerialException): WriteFile failed ([Error 22] The device does not recognize the command.)
[ERROR] Can't write to printer (disconnected?) (SerialException): WriteFile failed ([Error 22] The device does not recognize the command.)
[ERROR] Disconnecting after 4 failed writes.
Disconnected.
Connecting...
Printer is now online.
M115
SENDING:M115
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 1.21 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2018-03-21
M552
SENDING:M552
WiFi module is idle
M587 S"Linksys05XXX 2.4GHz" P"jXXXXXXaf"
SENDING:M587 S"LINKSYS05XXX 2.4GHZ" P"JXXXXXXAF"
M552 S1
SENDING:M552 S1
WiFi reported error: no known networks found
WiFi module is idle

So...

My SD card is (F)

I create 2 folders sys & www?

Hi,

I am confused...

I am not a PC expert or an expert in g code. I did build my own 3D printer using a Duet wifi.

I have just installed a new router and want the printer to be accessible via the web page as before with my old router.

I have been reading up on the method for connecting to a new router then noticed that if my FW was 1.18 I needed to update.

I arrived at this page but am now stumped by the comments put them in /sys on the SD card and empty /www folder. I am not allowed to create any folders with / in the folder name.

This might be a simple issue for you guys but I am now stuck.

Can I just have a process to use to get my printer connected to my new router using existing FW or can someone give me a blow by blow idiots guide to updating the FW...

Thanks.

Don

Hi, and yes I have read previous posts on this subject...

I have a new router and I am having trouble connecting my Duet to it.

I am on 1.15c firmware.

I can see the Duet as open in my available networks.

I get to the page that says Select Your WiFi Network.

However, it shows no networks...just WiFi password box and Duet host name box.

My issues are compounded because I cannot seem to connect to the Duet to my PC because I cannot find it on a com's port...

Yes, I am not very computer literate and must be missing some simple steps...

Can anyone help?

Thanks.

I will check the web release level. I am on 1.18.1

Thanks for the quick reply.

Don

Hi, new user, come to calibrate my CPU temp as it seems important from the discussions but no CPU temp read out on my webui!