Posts made by Hunterglory

@dc42 It works now! Thank you. I completely overlooked that part

@dc42 I just tried it and it does send the Gcode

M111 S1 P3
USB: M111 S1 P3
Debugging enabled for modules: Gcodes(3 - 0xffffffff)
Debugging disabled for modules: Platform(0) Network(1) Webserver(2) Move(4) Heat(5) Kinematics(6) InputShaping(7) unused(8) PrintMonitor(9) Storage(10) PortControl(11) DuetExpansion(12) FilamentSensors(13) WiFi(14) Display(15) SbcInterface(16) CAN(17) Expansion(18)
Aux: G91 G0 F6000 X0.1
Aux: G91 G0 F6000 X0.3
Aux: G91 G0 F6000 X0.3
Aux: G91 G0 F6000 X0.5
Aux: G91 G0 F6000 X-0.1
Aux: G91 G0 F6000 X-0.3
Aux: G91 G0 F6000 X-0.5
Aux: G91 G0 F6000 Y1.0
Aux: G91 G0 F6000 Y1.0
Aux: G91 G0 F6000 Y3.0
Aux: G91 G0 F6000 Y3.0
Aux: G91 G0 F6000 Y4.0
Aux: G91 G0 F6000 Y5.0
Aux: G91 G0 F6000 Y-1.0
Aux: G91 G0 F6000 Y-2.0
Aux: G91 G0 F6000 Y-3.0
Aux: G91 G0 F6000 Y-4.0
Aux: G91 G0 F6000 Y-5.0
Aux: G91 G0 F600 Z1.0
Aux: G91 G0 F600 Z3.0
Aux: G91 G0 F600 Z6.0
Aux: G91 G0 F600 Z5.0
Aux: G91 G0 F600 Z-1.0
Aux: G91 G0 F600 Z-2.0
Aux: G91 G0 F600 Z-3.0
Aux: G91 G0 F600 Z-3.0
Aux: G91 G0 F600 Z-5.0

@dc42 Could this be a software bug on the arduino side?

Hi!

I have wired and programmed the CNC Pendant according to the Arduino Pro Micro to Duet wiring section https://docs.duet3d.com/User_manual/Connecting_hardware/IO_CNC_Pendant.

I however can't seem to get it to work.

What Gcode do I need to write in my Config.g?

I added M575 P1 S1 B57600 and I can see that the arduino pro micro light gets turned on when I rotate the encoder. (a Green LED is turned on, a red LED is turned on and a dim red LED gets turned on when rotating the encoder)

My axis have been defined using:

; Smart Drivers
M569 P4 S1 D2 ; driver 0.0 goes forwards (X axis)
M569 P5 S1 D2 ; driver 0.1 goes forwards (Y axis)
M569 P3 S1 D2 ; driver 0.2 goes forwards (Z axis)

; Axes
M584 X4 Y5 Z3 ; set axis mapping
M350 X16 Y16 Z16 I1 ; configure microstepping with interpolation
M906 X4200 Y4200 Z4200 ; set axis driver currents
M92 X800 Y800 Z800 ; configure steps per mm
M208 X-3500:3500 Y-3500:3500 Z-2500:2500 ; set minimum and maximum axis limits
M566 X100 Y100 Z50 ; set maximum instantaneous speed changes (mm/min)
M203 X600 Y600 Z600 ; set maximum speeds (mm/min)
M201 X2000 Y2000 Z2000 ; set accelerations (mm/s^2)

The stop button does however send the Halt status to the duet 3

I am using a Duet 3 Mainboard 6HC V1.01A and plugged the connector into IO_0