@dc42 Australia. My guess is shipping alone would be more expensive than a new board.
Latest posts made by jonoharms
RE: Is My ToolBoard 1LC Dead?
Link to photos (click 'view original' to get the full quality photos. https://1drv.ms/u/s!An1MTmHeuUiDjt8adZsG_NLJ8H69BQ?e=R8Azs9
I can't see any obvious damage, no discoloration that I can see.
Definitely wired the motor wrong (don't ask me why, I don't know ). The motor cable I made goes (toolboard side -> motor side):
red (B-) -> green (A-)
black (B+) -> black (A+)
yellow (A-) -> red (B-)
white (A+) -> blue (B+)
I didn't double check the motor wiring before powering on, because I was also sure that if I did it wrong, it shouldn't destroy anything. From this wiring, I assume it might just go backwards. Can't see how this would have shorted anything.
The CAN cable I made is straight through (checked with multimeter). ie yellow = yellow, red = red etc.
As I said, this was working, then I disconnected it, made the new motor wire, CAN and power cables, and connected it back up, to find it not working. So I'm stumped.
Could it have been static damage?
RE: Is My ToolBoard 1LC Dead?
@o_lampe I'm 99% sure this is my own stupid fault, and therefore not covered under warranty, but holding out hope that it might be something easy to fix. But I doubt it. Just wanted a second opinion.
Pretty sure it was something to do with the motor cable I made (hemera -> toolboard). I had a second look at my other tool, and although I matched the colors, the pins locations don't match, so I think that must have been it.
Is My ToolBoard 1LC Dead?
Toolboards x2: 1LC with tool distribution board
Printer: Jubilee (core xy with toolchanger)
One of my toolboards is dead I think. When I power it on with nothing else connected and it not attached to the hemera, it gets the two solid red and blue leds, but no flashing red LED. The atmel chip gets very hot and there is a soft buzzing noise. Measured some continuity to check for a short, and get continuity between GND and 5V when not powered on. My guess is I shorted something.
The other toolboard is fine, and this toolboard was working a few days ago with the new firmware. I think I may have damaged something during the rewiring that I was doing.
Tried to do a reset using the button, but got no response. Disconnected all heaters, fans temp sensor. Removed from hemera to rule out a short.
Please let me know if there is anything else I can try. Also, not sure if this a warranty issue if it turns out it is dead.
RE: 3.2 beta 1 Freeze while printing
I'm getting the same intermittent freezing. Also seems to happen during toolchange procedure. Sometimes before toolchange, sometimes after.
Raspberry pi 4 8gb
Duet 3 MB6HC version 3.2-beta1
1x Toolboard with 3.2-beta
M122 === Diagnostics === RepRapFirmware for Duet 3 MB6HC version 3.2-beta1 running on Duet 3 MB6HC v1.01 or later (SBC mode) Board ID: 08DJM-956L2-G43S8-6J9FJ-3SJ6Q-980GG Used output buffers: 1 of 40 (22 max) === RTOS === Static ram: 154820 Dynamic ram: 133684 of which 32 recycled Exception stack ram used: 552 Never used ram: 104128 Tasks: HEAT(blocked,278) CanReceiv(blocked,880) CanSender(blocked,345) CanClock(blocked,352) TMC(blocked,18) MAIN(running,719) IDLE(ready,19) Owned mutexes: === Platform === Last reset 02:50:11 ago, cause: software Last software reset at 2020-09-26 15:22, reason: User, LinuxInterface spinning, available RAM 103944, slot 1 Software reset code 0x0010 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0444a000 BFAR 0x00000000 SP 0xffffffff Task MAIN Error status: 0x020 MCU temperature: min 36.8, current 37.7, max 39.8 Supply voltage: min 23.9, current 24.0, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes 12V rail voltage: min 12.1, current 12.1, max 12.2, under voltage events: 0 Driver 0: position 60000, standstill, reads 64470, writes 15 timeouts 0, SG min/max 0/434 Driver 1: position 0, standstill, reads 64469, writes 15 timeouts 0, SG min/max 0/509 Driver 2: position 11840, standstill, reads 64469, writes 15 timeouts 0, SG min/max 0/1023 Driver 3: position 0, standstill, reads 64469, writes 15 timeouts 0, SG min/max 0/1023 Driver 4: position 0, standstill, reads 64469, writes 15 timeouts 0, SG min/max 0/1023 Driver 5: position 0, standstill, reads 64472, writes 13 timeouts 0, SG min/max 0/104 Date/time: 2020-09-26 18:12:52 Slowest loop: 6.35ms; fastest: 0.21ms === Storage === Free file entries: 10 SD card 0 not detected, interface speed: 37.5MBytes/sec SD card longest read time 0.0ms, write time 0.0ms, max retries 0 === Move === Hiccups: 0(0), FreeDm: 375, MinFreeDm: 363, MaxWait: 2714285ms Bed compensation in use: mesh, comp offset 0.018 === MainDDARing === Scheduled moves: 6, completed moves: 6, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1 === AuxDDARing === Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1 === Heat === Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1 Heater 0 is on, I-accum = 0.3 === GCodes === Segments left: 0 Movement lock held by null HTTP* is ready with "M122" in state(s) 0 Telnet is idle in state(s) 0 File* is idle in state(s) 0 USB is idle in state(s) 0 Aux is idle in state(s) 0 Trigger* is idle in state(s) 0 Queue* is idle in state(s) 0 LCD is idle in state(s) 0 SBC is idle in state(s) 0 Daemon* is idle in state(s) 0 Aux2 is idle in state(s) 0 Autopause is idle in state(s) 0 Code queue is empty. === Network === Slowest loop: 0.00ms; fastest: 5726623.00ms Responder states: HTTP sessions: 0 of 8 - Ethernet - State: disabled Error counts: 0 0 0 0 0 Socket states: 0 0 0 0 0 0 0 0 === CAN === Messages sent 49377, send timeouts 49377, longest wait 2ms for type 6013, free CAN buffers 48 === SBC interface === State: 0, failed transfers: 0 Last transfer: 18ms ago RX/TX seq numbers: 4942/4944 SPI underruns 0, overruns 0 Number of disconnects: 0 Buffer RX/TX: 0/0-0 === Duet Control Server === Duet Control Server v3.2.0-beta1+1 File: Finishing macro retractprobe0.g, started by G1 X175.548 Y165.520 E1.65142 > Next stack level Suspended code: T0 Suspended code: M109 S205 ; set temperature and wait for it to be reached Suspended code: G21 ; set units to millimeters Suspended code: G90 ; use absolute coordinates Suspended code: M83 ; use relative distances for extrusion Suspended code: ; Filament gcode Suspended code: G1 Z0.350000 F7800.000 Suspended code: G1 E-0.40000 F3000.00000 Suspended code: G1 Z1.250000 F7800.000 Suspended code: G1 X127.199 Y127.882 Suspended code: G1 Z0.350000 Suspended code: G1 E0.45000 F3000.00000 Suspended code: G1 F1800.000 Suspended code: G1 X127.975 Y127.115 E0.05896 Suspended code: G1 X128.827 Y126.432 E0.05896 Suspended code: G1 X129.737 Y125.844 E0.05853 Suspended code: G1 X130.710 Y125.350 E0.05896 Suspended code: G1 X131.721 Y124.961 E0.05853 Suspended code: G1 X132.767 Y124.678 E0.05853 Suspended code: G1 X133.837 Y124.504 E0.05853 Suspended code: G1 X134.982 Y124.439 E0.06199 Suspended code: G1 X165.007 Y124.439 E1.62193 Suspended code: G1 X166.836 Y124.600 E0.09920 Suspended code: G1 X168.610 Y125.076 E0.09920 Suspended code: G1 X170.267 Y125.847 E0.09877 Suspended code: G1 X171.773 Y126.898 E0.09920 Suspended code: G1 X173.074 Y128.194 E0.09920 Suspended code: G1 X174.131 Y129.695 E0.09920 Suspended code: G1 X174.912 Y131.357 E0.09920 Suspended code: G1 X175.392 Y133.122 E0.09877 Pending code: G1 X175.561 Y134.950 E0.09920 Pending code: G1 X175.548 Y165.520 E1.65142 Code buffer space: 4096 Configured SPI speed: 8000000 Hz Full transfers per second: 32.60 File /opt/dsf/sd/gcodes/cube.gcode is selected, processing