Best posts made by juliann

@fcwilt

Hi Frederick! @fcwilt

Very good news, you found the solution!
I applied your suggestions and now the issue is totally fixed!

Thank you so much for all the help provided.

Julián.

Thank you @dc42

I did it but the problem persist, this is the temp 0 with the beta 5:

09/11/2021, 12:42:35	m122 b20
Diagnostics for board 20:
Duet TOOL1LC rev 1.1 or later firmware version 3.4.0beta5 (2021-10-12 13:59:06)
Bootloader ID: SAMC21 bootloader version 2.3 (2021-01-26b1)
Never used RAM 3032, free system stack 2789 words
Tasks: Move(notifyWait,0.0%,153) HEAT(notifyWait,0.1%,115) CanAsync(notifyWait,0.0%,64) CanRecv(notifyWait,0.0%,77) CanClock(notifyWait,0.0%,64) ACCEL(notifyWait,0.0%,61) TMC(notifyWait,2.9%,67) MAIN(running,92.1%,440) IDLE(ready,0.0%,27) AIN(delaying,4.9%,148), total 100.0%
Last reset 00:00:03 ago, cause: software
Last software reset time unknown, reason: AssertionFailed, available RAM 3392, slot 2
Software reset code 0x0120 ICSR 0x00000000 SP 0x2000415c Task  Freestk 129 bad marker
Stack: 00000544 00022ffc 00019b65 20003134 00016cff 20003134 000163d1 20000ed0 00000000 00000001 00008275 200071c8 200071c8 200071e0 00000000 20000f50 00011647 000223b8 00022474 00021ac8 00019b05 200071c8 200071c8 20000f50 000083ed 200071d8 000009c7
Driver 0: pos 0, 80.0 steps/mm, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 49, reads 1870, writes 9, timeouts 0, DMA errors 0, steps req 0 done 0
Moves scheduled 0, completed 0, in progress 0, hiccups 0, step errors 0, maxPrep 0, maxOverdue 0, maxInc 0, mcErrs 0, gcmErrs 0
Peak sync jitter -2/5, peak Rx sync delay 564, resyncs 0/0, no step interrupt scheduled
VIN voltage: min 24.0, current 24.0, max 24.0
MCU temperature: min 35.4C, current 35.4C, max 35.4C
Last sensors broadcast 0x00000000 found 0 42 ticks ago, loop time 0
CAN messages queued 59, send timeouts 0, received 45, lost 0, free buffers 37, min 37, error reg 0
dup 0, oos 0/0/0/0, bm 0, wbm 0, rxMotionDelay 0
Accelerometer detected: yes, status: 00
I2C bus errors 0, naks 3, other errors 0

Hi @achrn

Good news!
Just to confirm you, I put the SSR + config.g line to activate an output and this way solved completely my issue.

No more fan noise during boot or when I reset/ emergency stop the printer.

Thanks again for your help.
Julián.

Thank you @fcwilt

All slicer configurations were created based on findings that I came across on forums and Internet, I mean, they are there just by doing copy and paste...

Where should I start fixing or organising it?

@fcwilt

Thank you so much Frederick for taking the time, please enjoy your lunch

Hi Frederick @fcwilt

No problem at all, thanks again for taking all this time helping me.

I am checking and updating all the settings following your instructions and I will try another print. I will let you know the results tomorrow for sure.

Thank you very much!
Julián.