Posts made by KennyC

@Danal Thanks for your reply, Much appreciated, tried yet another SD card replaced the WWW folder "again" and all is well.
Like a lot of this it'll remain a mystery as to why in the first place!!!
Thanks.

Hi, Thanks for reply. I firstly re-formatted the card so it was empty, Tried to upload one file, same message, then I replaced the card.

Maestro firmware 2.05.1
Been having some great results with my Maestro right up until yesterday.

First issue whilst trying to upload print file was "error unable to upload file card may be full" (or words to that effect)

Second almost immediately I could no longer access DWC.

I have replaced the SD card and can open the DWC page but all areas are "greyed out" rendering it unusable.
I can still print by inserting the SD card into the Paneldue but its just not as user friendly.
Bit of a faff re-installing firmware without DWC

Any Help appreciated.

@dc42

Many Thanks for that, Nope I had not, Thankfully now working,
Any Thoughts on why Fan 0 is inop?
Thanks Kenny.

Hi Paul many thanks for your reply,

M115
FIRMWARE_NAME: RepRapFirmware for Duet 2 Maestro FIRMWARE_VERSION: 2.05.1 ELECTRONICS: Duet Maestro 1.0 FIRMWARE_DATE: 2020-02-09b1

Fan works fine connected to PSU

On Fan 0 the Fan does not work at all.
If I connect it to Fan 1 it works and I can control the speed with the slider in DWC
However the hot end ,hot end fan and LED's on the smart effector does not work on Fan 0

I can change the Part cooling fan to Fan 2 and it works but is really under powered.

Thanks Kenny.

Some Help Please, I've been at this for 3 days !!
Wiring is sound,
Fan 0 Part cooling
Fan 1 Hot end

I cannot make the part cooling fan work.
If I swap connections the part cooling fan works but the hot end, hot end fan and LED's on the smart effector will not.

This is driving me spare, any assistance would be appreciated.

; Configuration file for Duet Maestro (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Sat Mar 21 2020 22:23:28 GMT+0000 (Greenwich Mean Time)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Predator" ; set printer name
M665 R227 L440.42 B85 H410 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0 ; put your endstop adjustments here, or let auto calibration find them

; Network
M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S0 ; physical drive 0 goes backwards
M569 P1 S0 ; physical drive 1 goes backwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S0 ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 E16 I0 ; configure microstepping without interpolation
M350 X16 Y16 Z16 I1 ; configure microstepping with interpolation
M92 X160.00 Y160.00 Z160.00 E436.54 ; set steps per mm
M566 X1200.00 Y1200.00 Z1200.00 E1200.00 ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z18000.00 E1200.00 ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z1000.00 E1000.00 ; set accelerations (mm/s^2)
M906 X1000 Y1000 Z1000 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 Z0 S1 ; set minimum Z

; Endstops
M574 X2 Y2 Z2 S1 ; set active high endstops

; Z-Probe
M558 P8 R0.4 F1200 ; set Z probe type to effector and the dive height + speeds
M558 H30 ;*** Remove this line after delta calibration has been done and new delta parameters have been saved
G31 P100 X0 Y0 Z-0.1 ; set Z probe trigger value, offset and trigger height
M557 R85 S20 ; define mesh grid

; Heaters
M305 P0 T100000 B4138 R2200 ; set thermistor + ADC parameters for heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M305 P1 T100000 B4725 C7.060000e-8 R2200 ; set thermistor + ADC parameters for heater 1
M143 H1 S300 ; set temperature limit for heater 1 to 300C

; Fans
M106 P0 S0 I0 F500 H-1 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501 ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

Thanks very much for both replies, Turned out to be a faulty "brand new" Ethernet cable, sorted now ,
Thanks Kenny.

Fast response thanks,
" site cannot be reached" took to long to respond.
Spat the dummy and reformatted the card, currently empty.

I've lost count of the variations I've had on the card, all probably wrong through frustration.
What is the correct files to have on the card and where should they be and in what order.

Its a tall order but I would appreciate your help.
Thanks Kenny.

HI All,
At my wits end with this and need some help with my Maestro Please.
Cannot for the life of me connect to DuetWebControl.
Firmware OK M115 returns correct version (2.05.1)
IP address done , shows connected on my router.

I've lost count of the connection attempts, suffice so say its driving me up the wall.

I've also lost patience switching from page to forum to page and back again , There really should be a more concise way of doing this if it doesn't work out the box other than trolling forums and the internet endlessly picking up fragments of information,
OK I'll stop nagging now.

Someones help would be greatly appreciated.
Thanks in advance Kenny.