Posts made by kgrigio

Perfect! Thanks, that did the trip. I am now officially fully converted over to a duet 2 setup!

I should note that when I auto home or do a bed level or manually move the bed or z axis, the printer speeds are fast and match what I have in the config.g file, so I am pretty confident it is something to do with the cura slicer. I am using cura 4.7.1.

I have spent all day working through my configurations and finally have things working. I swapped from a stock ender CR-10 v2 controller to the duet 2 wifi. When I was printing with the stock controller, my cura slicer was all set up and working fine. I didn't make any changes in the cura slicer other than changing the gcode flavor from Marlin to RepRap, which I assume is correct.

The issue is the printer is now gawd awful slow and pauses a lot within the same layer. I am not sure what other changes need to be made in the cura slicer to finally get the printer to print like it was with the stock controller running Marlin 2.0x bugfix.

Here is the start of my gcode in the machine settings of cura. I already commented out the M420 S1 command as that threw and error the first time I tried to run a print.

Anything else I need to do now that I have switched to a Duet 2?

By the way, I tried printer by loading the file over the web interface and via the SD card, all with the same results.

Thanks.

M201 X500.00 Y500.00 Z100.00 E5000.00 ;Setup machine max acceleration
M203 X500.00 Y500.00 Z10.00 E50.00 ;Setup machine max feedrate
M204 P500.00 R1000.00 T500.00 ;Setup Print/Retract/Travel acceleration
M205 X8.00 Y8.00 Z0.40 E5.00 ;Setup Jerk
M220 S100 ;Reset Feedrate
M221 S100 ;Reset Flowrate

M280 P0 S160 ;BLTouch alarm release
G28 ;Home
;M420 S1

G92 E0 ;Reset Extruder
G1 Z2.0 F3000 ;Move Z Axis up
G1 X10.1 Y20 Z0.28 F5000.0 ;Move to start position
G1 X10.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line
G1 X10.4 Y200.0 Z0.28 F5000.0 ;Move to side a little
G1 X10.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line
G92 E0 ;Reset Extruder
G1 Z2.0 F3000 ;Move Z Axis up

Perfect. Thanks.

Yes, now I am reading as follows

M574
Endstop configuration:
X: low end switch connected to pin xstop
Y: low end switch connected to pin ystop
Z: low end Z probe

On the thermistors you mentioned above. What didn't I configure correctly? I haven't looked at this closely yet as I am going between this and helping my kids with virtual school today. Thanks again for the help.

Perfect. Thanks for the help. Now on to fix the other items, like the endstops you pointed out.

What I pasted above is from the file management -> systems -> config.g file, but I just figured it out. When I opened the file, I then hit save and it now works.

This begs the question, when I upload a new configuration.zip file why wouldn't this automatically save and start being used? Do I need to go in and save every time I upload? Do I need to save all the files?

What is on the duet, at least I think. I uploaded the system files from my configuration zip file. Do I need to do anything once I upload them to make them "take"

M574

Endstop configuration:
X: none
Y: none
Z: none

M115
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.1.1 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2020-05-19b2

I am new to the duet platform and reprap firmware. I am very comfortable with Marlin firmware. Here is what is going on. I recently purchased a duet 2 wifi and wired it to my Ender CR-10 v2 that was working with the stock ender controller. I also have a bltouch wired onto the printer.

The duet had firmware 2.05.1 and I immediately upgraded it to firmware 3.0 then to 3.1.1. I then ran the web configurator tool to generate my zip file, which I uploaded to the board.

I am just trying to get the basics working and I can't get the endstops working. I wired in the NC end stops and the led on the board is lit when the endstop isn't pressed and turns off when it is pressed.

The issue is when I type the M119 command I am getting

Endstops - X: no endstop, Y: no endstop, Z: no endstop, Z probe: not stopped

Nothing I do makes a change and I am pulling my hair out.

Here is my config.g file

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Tue Sep 15 2020 09:37:17 GMT-0500 (Central Daylight Time)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Deere_CR10_v2" ; set printer name

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E420.00 ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X300 Y300 Z400 S0 ; set axis maxima

; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S2 ; configure Z-probe endstop for low end on Z

; Z-Probe
M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X47 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height
M557 X15:285 Y15:285 S20 ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 C"E_Fan" S1 H-1 ; set fan 0 name and value. Thermostatic control is turned off
M950 F1 C"fan2" Q500 ; create fan 1 on pin fan2 and set its frequency
M106 P1 C"E_Fan_PWM" S0 H1 T45 ; set fan 1 name and value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss