Adding M558 P4 to homez.g solved my problem

The sensor is triggering correct.
the sensor LED lights up, but the z move doesn't stop,
i will come back with more info on sunday when I am back at my printer

Hello,

I really need HELP.

I replaced my IR sensor with an capacitive sensor and when using G30 befor any homing the sensor stopps perfectly above the heatbed like calibrated.
but as soon I am homing X or Y or using G30 in a script the G30 is not stopping and drives into the heatbed.

Any Idea?

here are my config files:

; Configuration file for RepRap Mendel 3
; RepRapPro Ltd
;
; Copy this file to config.g if you have a Mendel 3
; If you are updating a config.g that you already have you
; may wish to go through it and this file checking what you
; want to keep from your old file.
;
M111 S0 ; Debug off
M550 PRepRapPro Mendel 3 ; Machine name (can be anything you like)
M551 Preprap ; Machine password (currently not used)
M540 P0xBE:0xEF:0xDE:0xAD:0xFE:0x14 ; MAC Address
M552 P192.168.1.14 ; IP address
M553 P255.255.255.0 ; Netmask
M554 P192.168.1.1 ; Gateway
M555 P2 ; Set output to look like Marlin
G21 ; Work in millimetres
G90 ; Send absolute corrdinates…
M83 ; ...but relative extruder moves
M558 P4 Y0 X0 Z1 I1 ; Use a capacitive NPN Z probe
M574 X1 Y1 ; set endstop configuration (Y endstop only, at low end, active high)
G31 Z0.1 P800 ; Set the probe height and threshold (deliberately too high to avoid bed crashes on initial setup)
M906 X800 Y1000 Z800 E800 ; Set motor currents (mA)
;M305 P0 R4700 H0 L0 ; Set the heated bed thermistor series resistor to 4K7
;M305 P1 R4700 H0 L0 ; Set the hot end thermistor series resistor to 4K7
;M305 P2 R4700 H0 L0 ; Set the hot end thermistor series resistor to 4K7
M569 P0 S1 ; Reverse the X axis
M569 P3 S0 ; Reverse the Z axis
M92 E660:660:660 ; Set extruder steps per mm
G31 Z0.1 P600 ; Set the probe height and threshold (deliberately too high to avoid bed crashes on initial setup)
M556 S78 X0 Y0 Z0 ; Put your axis compensation here
M201 X3000 Y3000 Z150 E500 ; Accelerations (mm/s^2)
M203 X15000 Y15000 Z100 E3600 ; Maximum speeds (mm/min)
M566 X200 Y200 Z30 E20 ; Minimum speeds mm/minute
M208 X-8 S1 ; Set axis minimum (adjust to make X=0 the edge of the bed)
M208 X214 Y210 ; Set axis maxima (adjust to suit your machine)
M563 P0 D0 H1 ; Define tool 0
G10 P0 S-273 R-273 ; Set tool 0 operating and standby temperatures

---

homez.g is:

G91
G1 Z5 F2000
G90
G1 X52 Y22
G30
G1 Z0 F1000

---

Hello,

yes
with G30 it stops

homez is above in the thread added.
homeall is :

G91
G1 Z5 F200
G90
G1 Y-240 X-300 F2000 S1
G91
G1 X3 Y3 F2000
G1 X-10 Y-10 F200 S1
G90
G1 X60 Y0 F6000
G30
G1 Z5

as soon i am moving the head to another position the z probe is no longer stopping the head…...

using G30 in the console it works

when used in script it isn't

Hello !

I need some help
I connected the Capacitive NPN Probe to E0 Endstop and it is recognized with M119 also E0 enstop LED lights up
In the duet web control the Z probe is shown with value 1000 when sensor is triggered.:

M119
Endstops - X: not stopped, Y: not stopped, Z: at min stop, Z probe: at min stop

But when homing Z the movement is not stopping when the min stop is triggered.

My config.g is like this:

---

; Configuration file for RepRap Mendel 3
; RepRapPro Ltd
;
; Copy this file to config.g if you have a Mendel 3
; If you are updating a config.g that you already have you
; may wish to go through it and this file checking what you
; want to keep from your old file.
;
M111 S0 ; Debug off
M550 PRepRapPro Mendel 3 ; Machine name (can be anything you like)
M551 Preprap ; Machine password (currently not used)
M540 P0xBE:0xEF:0xDE:0xAD:0xFE:0x14 ; MAC Address
M552 P192.168.1.14 ; IP address
M553 P255.255.255.0 ; Netmask
M554 P192.168.1.1 ; Gateway
M555 P2 ; Set output to look like Marlin
G21 ; Work in millimetres
G90 ; Send absolute corrdinates…
M83 ; ...but relative extruder moves
M558 P4 Y0 X0 Z1 I1 ; Use a capacitive NPN Z probe
M574 X1 Y1 ; set endstop configuration (Y endstop only, at low end, active high)
G31 Z0.1 P800 ; Set the probe height and threshold (deliberately too high to avoid bed crashes on initial setup)
M906 X800 Y1000 Z800 E800 ; Set motor currents (mA)
;M305 P0 R4700 H0 L0 ; Set the heated bed thermistor series resistor to 4K7
;M305 P1 R4700 H0 L0 ; Set the hot end thermistor series resistor to 4K7
;M305 P2 R4700 H0 L0 ; Set the hot end thermistor series resistor to 4K7
M569 P0 S1 ; Reverse the X axis
M569 P3 S0 ; Reverse the Z axis
M92 E660:660:660 ; Set extruder steps per mm
G31 Z0.1 P600 ; Set the probe height and threshold (deliberately too high to avoid bed crashes on initial setup)
M556 S78 X0 Y0 Z0 ; Put your axis compensation here
M201 X3000 Y3000 Z150 E500 ; Accelerations (mm/s^2)
M203 X15000 Y15000 Z100 E3600 ; Maximum speeds (mm/min)
M566 X200 Y200 Z30 E20 ; Minimum speeds mm/minute
M208 X-8 S1 ; Set axis minimum (adjust to make X=0 the edge of the bed)
M208 X214 Y210 ; Set axis maxima (adjust to suit your machine)
M563 P0 D0 H1 ; Define tool 0
G10 P0 S-273 R-273 ; Set tool 0 operating and standby temperatures

---

homez.g is:

G91
G1 Z5 F2000
G90
G1 X52 Y22
G30
G1 Z0 F1000

---

Any idea ?

Regards,

Jörn