Posts made by lecman93

thank you very much it's good everything works

thank you very much, I did not understand at all that the command G1 worked in a sense.

It works well as it takes.

For HomeAll.g I made the change thanks again.

So for the U axis that does not change value, this is normal I do not have to worry?

Hello,
My name is Damien, I've been printing for over 2 years now.
I embarked on the design and manufacture of a Core XY using X and Y rail, with a printing surface of 30x30x60.

I am currently finishing the machine and since then I have some problems that I did not have before.
Already I have 2 independent Z motor with each endstop at the bottom of the printer and a BLTouch sensor at the top.
Until there can all worked well but since I received my hotend and I installed it, I encounter 2 problems.

The first when I make a G1 Z-100 F2400 for example the bed will always go to the value 0, whatever the value indicated, The X and Y axis behaves normally.
By cons if I use the movement of the panel due or the web interface I do not encounter the problem

Second problem, when I make a move in Z thanks to the paneldue or the web interface, the value Z changes well but not my U value of my second Z axis, but physically it moves correctly.

Config.g

; General preferences
M111 S0 ; Debugging off
G21 ; Work in millimetres
G90 ; Send absolute coordinates…
M83 ; ...but relative extruder moves
M555 P2 ; Set firmware compatibility to look like Marlin

M667 S1 ; Select CoreXY mode
M584 X0 Y1 Z2:5 U5 E3:4 ; three Z motors connected to driver outputs 2, 5 and 6
;M671 X-39:359 Y151.07:151.07 ; leadscrews at leftand right

; Axis Limits
M208 X0 Y0 Z0 U0 S1 ; Set axis minima
M208 X320 Y310 Z628 U628 S0 ; Set axis maxima
M564 H0 ; Limit axes

;Physical Drive conextion
M569 P0 S0 ; Drive 0 goes forwards X
M569 P1 S0 ; Drive 1 goes forwards Y
M569 P2 S1 ; Drive 2 goes forwards Z gauche
M569 P3 S1 ; Drive 3 goes forwards E0
M569 P4 S1 ; Drive 4 goes forwards E1
M569 P5 S1 ; Drive 5 goes forwards Z droite
M569 P6 S1 ; Drive 6 goes forwards vide

; Endstops
M574 X1 Y1 S1 ; Set active low endstops
M574 Z2 U2 S1 ; Set active high endstops

;Bltouch
M307 H4 A-1 C-1 D-1
M558 P9 H5 F200 T5000 A2 ; Set Z probe type to switch and the dive height + speeds
G31 P25 X22.75 Y17.3 Z1.1188 U1.1188 ; Set Z probe trigger value, offset and trigger height
M557 X5:295 Y5:295 S40 ; Define mesh grid

; Configure Drives
M350 X16 Y16 Z16 U16 E16:16 I1 ; Configure microstepping with interpolation
M92 X80 Y80 Z400 U400 E2750:2750 ; Set steps per mm
M566 X900 Y900 Z12 U12 E40:40 ; Set maximum instantaneous speed changes (mm/min)
M203 X18000 Y18000 Z2400 U2400 E1800:1800 ; Set maximum speeds (mm/min)
M201 X1000 Y1000 Z250 U250 E120:120 ; Set accelerations (mm/s^2)
M906 X1300 Y1300 Z1300 U1300 E1300:1300 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Heaters
M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S150 ; Set temperature limit for heater 0 to 150C
M305 P1 T100000 B4388 C7.060000e-8 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S285 ; Set temperature limit for heater 1 to 300C
M305 P2 T100000 B4388 C7.060000e-8 R4700 ; Set thermistor + ADC parameters for heater 2
M143 H2 S285 ; Set temperature limit for heater 2 to 300C

; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X9 Y0 Z0 U0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
M563 P1 D1 H2 ; Define tool 1
G10 P1 X-9 Y0 Z0 U0 ; Set tool 1 axis offsets
G10 P1 R0 S0 ; Set initial tool 1 active and standby temperatures to 0C

;Save print low current
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 U3 E-5 F1000"

; Network
M550 PUltraCube ; Set machine name
M552 S1 ; Enable network

;*** Access point is configured manually via M587 by the user
M586 P0 S1 ; Enable HTTP
M586 P1 S1 ; Enable FTP
M586 P2 S1 ; Enable Telnet

; Fans
M106 P0 S0 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1:2 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S0 ; Set fan 2 value, LED. Thermostatic control is turned off

Bed.g

M561 ; clear any existing bed transform
G1 Z-628 F2400
G4 P500
G29 S2
G29
G1 S0 X0 Y0 F5000 ; move the head to the corner (optional)

HomeZ.g

G91 ; relative positioning
M584 Z2 U5
G1 Z1 U1 F6000 ; lift Z relative to current position
G1 S1 Z631 U631 F2400 ; move Z up until the switch triggers
G1 Z-10 U-10 F2400 ; go back a few mm
G1 S1 Z631 U631 F360 ; move slowly to Z axis endstop once more (second pass)
M584 Z2:5 U5
G90

HomeAll.g

G91 ; relative positioning
G1 Z5 U5 F6000 ; lift Z relative to current position
G1 S1 X-325 Y-315 F3000 ; move quickly to X or Y endstop and stop there (first pass)
G1 S1 X-325 ; home X axis
G1 S1 Y-315 ; home Y axis
G1 X5 Y5 F3000 ; go back a few mm
G1 S1 X-325 F360 ; move slowly to X axis endstop once more (second pass)
G1 S1 Y-315 F360 ; then move slowly to Y axis endstop
G1 S1 Z630 U630 F1800 ; move Z up stopping at the endstop (first pass)
G1 Z-5 U-5 F2400 ; go back a few mm
G1 S1 Z630 U630 F360 ; move slowly to Z axis endstop once more (second pass)
G90 ; absolute positioning

Thank you for your help because it's been several days that I look without finding the problem