Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. MichaudTime
    • Profile
    • Following 0
    • Followers 0
    • Topics 2
    • Posts 3
    • Best 0
    • Controversial 0
    • Groups 0

    MichaudTime

    @MichaudTime

    0
    Reputation
    1
    Profile views
    3
    Posts
    0
    Followers
    0
    Following
    Joined Last Online

    MichaudTime Unfollow Follow

    Latest posts made by MichaudTime

    • RE: Having Some bed leveling issues

      Well...... I'm dumb... swapped which spots the motors were plugged into and BAM. works great......

      Moral of the story... don't be like me

      posted in General Discussion
      MichaudTimeundefined
      MichaudTime
    • Having Some bed leveling issues

      So I have a 400X400 printer with two Z axis motors. I figured I would try to use them to help with bed compensation, they work great moving them up and down but when I run the calibration script it does the probing and then it compensates the wrong direction (it tilts the bed even further). I'm not sure why. Any thoughts?

      CONFIG.G
      
      ; General preferences
      G90                                      ; Send absolute coordinates...
      M83                                      ; ...but relative extruder moves
      
      M667 S1                                  ; Select CoreXY mode
      
      ; Network
      M550 P"SpazCube"                         ; Set machine name
      M552 P0.0.0.0 S1                         ; Enable network and acquire dynamic address via DHCP
      M586 P0 S1                               ; Enable HTTP
      M586 P1 S0                               ; Disable FTP
      M586 P2 S0                               ; Disable Telnet
      
      
      ; Custom Configuration
      M584 X0 Y1 Z2:4 E3                	; Set Z motors on drives 2 and 4
      M671 X-30.0:430.0 Y0:0 S4 		; Set the Z motor relative locations
      M208 X0:400 Y0:400			; X carriage moves from -5 to 205, Y bed goes from 0 to 200
      
      ; Drives
      M569 P0 S1                               ; Physical drive 0 goes forwards
      M569 P1 S1                               ; Physical drive 1 goes forwards
      M569 P2 S1                               ; Physical drive 2 goes forwards
      M569 P3 S0                               ; Physical drive 3 goes forwards
      M350 X32 Y32 Z32 E16 I0                  ; Configure microstepping  without interpolation
      M92 X200 Y200 Z799.10 E409               ; Set steps per mm
      M566 X350.00 Y350.00 Z12.00 E3000.00      ; Set maximum instantaneous speed changes (mm/min)
      M203 X9000.00 Y9000.00 Z450.00 E3600.00  ; Set maximum speeds (mm/min)
      M201 X500.00 Y500.00 Z20.00 E5000.00       ; Set accelerations (mm/s^2)
      M906 X800.00 Y800.00 Z900.00 E1000.00 I30 ; Set motor currents (mA) and motor idle factor in per cent
      M84 S30                                  ; Set idle timeout
      
      ; Axis Limits
      M208 X0 Y0 Z0 S1                         ; Set axis minima
      M208 X400 Y400 Z500 S0                   ; Set axis maxima
      
      ; Endstops
      M574 X0 Y0 Z0 S0                         ; Set active low and disabled endstops
      
      ; Z-Probe
      M558 P9 H5 A5 F120 T6000                 ; Disable Z probe but set dive height, probe speed and travel speed
      M557 X60:350 Y50:350 S50                 ; Define mesh grid  
      G31 P600 X59.5 Y0 Z2.10
      
      ; Heaters
      M305 P0 T100000 B4138 R2200              ; Set thermistor + ADC parameters for heater 0
      M143 H0 S120                             ; Set temperature limit for heater 0 to 120C
      M305 P1 T100000 B4138 R2200              ; Set thermistor + ADC parameters for heater 1
      M143 H1 S280                             ; Set temperature limit for heater 1 to 280C
      
      ; Fans
      M106 P0 S0 I0 H-1 B1                     ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
      M106 P1 S1 I0 F500 H1 T45                ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
      
      ; Tools
      M563 P0 D0 H1                            ; Define tool 0
      G10 P0 X0 Y0 Z0                          ; Set tool 0 axis offsets
      G10 P0 R0 S0                             ; Set initial tool 0 active and standby temperatures to 0C
      
      
      CALIBRATE CODE
      
      ; Warm Hotend and Bed
      T0			; Select Tool 0
      M104 S130		; Set Tool 0 temperature to 130 - no wait
      M190 S60		; Set Bed temperature to 60 - wait
      
      ; Clear Values
      G29 S2			; Clear Mesh Compensation Values
      M290 R0 S0      	; Clear Baby-stepping
      
      ; Home all Axes
      G28
      
      ; Bed leveling (G32)
      G30 P0 X60 Y200 Z-99999 	; probe near a leadscrew
      G30 P1 X360 Y200 Z-99999 S2 	; probe near a leadscrew and calibrate 2 motors
      
      posted in General Discussion
      MichaudTimeundefined
      MichaudTime
    • Wyze Cam 2 not updating

      Hey guys! I just got my Wyze Cam installed and the firmware updated and it's working well. I enabled it on the duet and now I'm having some issues. The image only refreshes if I refresh the whole web page. I've got it set using https://xxx.xxx.xxx.xxx/cgi-bin/currentpic.cgi? (Using my correct IP of Course) and right now I have the update interval set to 1. Any info to help out would be great! Thanks!

      posted in Duet Web Control
      MichaudTimeundefined
      MichaudTime