Hi, i am new to the 3d printing comunity.
I am trying to create a cartesian style custom 3d printer with the duet 2 ethernet and the duex 5 and i need some help.
I dont know why but the z wont home at all and the wen i send the commend for the x and y it takes a long time to respond and also when it used to work i was not able to make the mesh compensation work at all.
My bed goes up and down on the z and i have two motor, one for the front and one for the back whit a limit switch at the bottom for each of them and i also have a bltouch on my hotend.
For my x have one motor and for my y i have two motor, with their own separate limit switch.
And juste so you know i am 16 and i still my printer is at school so i can juste work on it durring lunch and one more thing sorry if my english is bad i speak frech.
This is the config.g
........................................................................................................................................................................................................................................................................................
; Configuration file for Duet WiFi (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.16 on Sat Sep 09 2023 15:18:43 GMT-0400 (heure d’été de l’Est nord-américain)
; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P7 S0 ; physical drive 7 goes backwords
M569 P5 S1 ; physical drive 5 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M569 P6 S0 ; physical drive 6 goes backwords
M569 P8 S0 ; physical drive 8 goes backwords
M584 X0 Y7:8 Z5:6 E3 ; set drive mapping
M350 X16 Y16:16 Z16:16 E16 I1 ; configure microstepping with interpolation
M92 X160.00 Y160.00:160.00 Z250.00:250.00 E829.00 ; set steps per mm
M566 X1200.00 Y1200.00:1200.00 Z200.00:200.00 E1200.00 ; set maximum instantaneous speed changes (mm/min)
M203 X12000.00 Y12000.00:12000.00 Z450.00:450.00 E12000.00; set maximum speeds (mm/min)
M201 X750.00 Y750.00:750.00 Z50.00:50.00 E400.00 ; set accelerations (mm/s^2)
M906 X1300 Y1300:1300 Z1300:1300 E1300 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 X0 Y25 Z0 S1 ; set axis minima
M208 X395 Y406 Z383 S0 ; set axis maxima
; Endstops
M574 X1 S1 P"!xstop" ; configure switch-type (e.g. microswitch) endstop for low end on X via pin xstop
M574 Y1 S1 P"!duex.e4stop+!duex.e5stop" ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin ystop
M574 Z1 S1 P"!duex.e2stop+!duex.e3stop" ; configure switch-type (e.g. microswitch) endstop for low end on Z via pin zstop
; Z-Probe
M950 S0 C"duex.pwm5" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H420 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X36.31584 Y30.47474 Z3.5 ; set Z probe trigger value, offset and trigger height
M557 X0:350 Y25:375 S35 ; define mesh grid
; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 R0.645 K0.203:0.000 D3.68 E1.35 S1.00 B0 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 R5.101 K0.728:0.085 D4.95 E1.35 S1.00 B0 V23.6 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S350 ; set temperature limit for heater 1 to 350C
; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S0 H1 T45 ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"fan2" Q500 ; create fan 2 on pin fan2 and set its frequency
M106 P2 S0 H-1 ; set fan 2 value. Thermostatic control is turned off
; Tools
M563 P0 S"PrintHead" D0 H1 F2:0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
; Custom settings are not defined
........................................................................................................................................................................................................................................................................................
This is the homeall.g
........................................................................................................................................................................................................................................................................................
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.3.16 on Sat Sep 09 2023 15:18:43 GMT-0400 (heure d’été de l’Est nord-américain)
G91 ; relative positioning
G1 H1 X-400 Y-386 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F6000 ; go back a few mm
G1 H1 X-10 Y-100 F6000 ; move slowly to X and Y axis endstops once more (second pass)
G1 H1 Z430 F500 ; move Z down stopping at the endstop
G90 ; absolute positioning
G92 X0 Y0 Z382
; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z420 F100 ; lift Z relative to current position
;G90 ; absolute positioning
........................................................................................................................................................................................................................................................................................
This is homex.g
........................................................................................................................................................................................................................................................................................
; called to home the X axis
;
; generated by RepRapFirmware Configuration Tool v3.3.16 on Sat Sep 09 2023 15:18:43 GMT-0400 (heure d’été de l’Est nord-américain)
G91 ; relative positioning
G1 H1 X-395 F1800 ; move quickly to X axis endstop and stop there (first pass)
G1 H2 X5 F6000 ; go back a few mm
G1 H1 X-395 F360 ; move slowly to X axis endstop once more (second pass)
G90 ; absolute positioning
........................................................................................................................................................................................................................................................................................
This is homey.g
........................................................................................................................................................................................................................................................................................
; called to home the Y axis
;
; generated by RepRapFirmware Configuration Tool v3.3.16 on Sat Sep 09 2023 15:18:43 GMT-0400 (heure d’été de l’Est nord-américain)
G91 ; relative positioning
G1 H1 Y-436 F1800 ; move quickly to Y axis endstop and stop there (first pass)
G1 H2 Y5 F6000 ; go back a few mm
G1 H1 Y-436 F360 ; move slowly to Y axis endstop once more (second pass)
G90 ; absolute positioning
........................................................................................................................................................................................................................................................................................
This is homez.g
........................................................................................................................................................................................................................................................................................
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool v3.3.16 on Sat Sep 09 2023 15:18:43 GMT-0400 (heure d’été de l’Est nord-américain)
G91 ; relative positioning
G1 H1 Z430 F1800 ; move Z down until the endstop is triggered
G92 Z382 ; set Z position to axis minimum (you may want to adjust this)
; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z420 F100 ; lift Z relative to current position
;G90 ; absolute positioning
........................................................................................................................................................................................................................................................................................
And this is a link to a photo of my custome printer https://drive.google.com/file/d/1j87pvdFDcpzuBPFj9EFopOtFatH9wOIZ/view?usp=sharing