Hi dc42
With the M552 S1 I had started the duet3d Server but the settings were not there. Then I saw that the config.g was renamed to config.g.bak, I renamed it back to config.g and everything was good. But the thing now is, after a few restarts, it renamed again the config.go to config.g.bak and I must manual start the WIFI server.
Hi
here the info when I send M122
Connecting…
ok T B:2000.0 /0.0
Printer is now online.
ok T B:2000.0 /0.0
M122
SENDING:M122
=== Diagnostics ===
Used output buffers: 1 of 32 (1 max)
=== Platform ===
RepRapFirmware for Duet WiFi version 1.19.2 running on Duet WiFi 1.0
Board ID: 08DDM-9FAM2-LW4S8-6J9D4-3S46S-92Z7X
Static ram used: 21176
Dynamic ram used: 95528
Recycled dynamic ram: 2080
Stack ram used: 4048 current, 4872 maximum
Never used ram: 7416
Last reset 00:00:25 ago, cause: power up
Last software reset reason: User, spinning module GCodes, available RAM 7996 bytes (slot 2)
Software reset code 0x0003, HFSR 0x00000000, CFSR 0x00000000, ICSR 0x00400000, BFAR 0xe000ed38, SP 0xffffffff
Error status: 0
[ERROR] Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms
MCU temperature: min 27.4, current 31.1, max 31.2
Supply voltage: min 0.0, current 0.6, max 0.7, under voltage events: 0, over voltage events: 0
Driver 0: ok
Driver 1: ok
Driver 2: ok
Driver 3: ok
Driver 4: ok
Date/time: 1970-01-01 00:00:00
Slowest main loop (seconds): 0.000149; fastest: 0.000032
=== Move ===
MaxReps: 0, StepErrors: 0, FreeDm: 240, MinFreeDm 240, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heater = 0, chamber heater = -1
=== GCodes ===
Segments left: 0
Stack records: 0 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "M122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
Network state is disabled
WiFi module is disabled
HTTP sessions: 0 of 8
Socket states: 0 0 0 0 0 0 0 0
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
Hi Duet3D forum
This April I bought a Duet3D board. Great Product - love it.
On Wednesday I printed a little part ( maybe 1 hour print ).
One day after I started the Printer and I could not connect with wifi.
My first reaction was, connecting with USB and Pronterface.
No problem, I can connect and the printer is online.
I can move in Z.
but when I send G28 it comes ->
homing file
homeall.g not found
I checked the SdCard on my PC and everything was okay.
What I tried
3 various SD Cards - all the same problem
Install new firmware -> comes Error 6
Can someone help me, please?
Thanks to all.