• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login
  1. Home
  2. ObiJohn
  3. Posts
  • Profile
  • Following 0
  • Followers 0
  • Topics 2
  • Posts 5
  • Best 1
  • Controversial 0
  • Groups 0

Posts made by ObiJohn

  • RE: Updated to firmware 3.5.0 b2 now 1lc not extruding

    I wanted to say thank you that solved my extrusion issue. Thank you very much!

    posted in Firmware installation
    undefined
    ObiJohn
    19 Mar 2023, 04:45
  • RE: Updated to firmware 3.5.0 b2 now 1lc not extruding

    @ObiJohn damn I missed that in the docs yes i had the allow cold extrudes command in the config. I have commented it out so we shall see. When I was trying to extrude I was at temp 195c on the extruder. but we shall see

    posted in Firmware installation
    undefined
    ObiJohn
    19 Mar 2023, 03:49
  • Updated to firmware 3.5.0 b2 now 1lc not extruding

    Hello all I updated from 3.4.5 to 3.5.0 b2. I have a duet 3 6hc with a toolboard 1lc connected via can at address 121. after the update i can no longer extrude from the toolboard connected stepper. if i revert back to 3.4.5 it will work again. I am also haveing issues with both versions stopping in the middle of a print saying it is finished when it has only done a very small part. what do you need going forward to fix these issues? here is the M122 and the M122 B121

    M122
    === Diagnostics ===
    RepRapFirmware for Duet 3 MB6HC version 3.5beta2 (2023-02-08 15:27:50) running on Duet 3 MB6HC v1.01 (SBC mode)
    Board ID: 08DJM-956L2-G43S8-6JTDD-3SJ6N-TB0YG
    Used output buffers: 1 of 40 (17 max)
    === RTOS ===
    Static ram: 154344
    Dynamic ram: 84112 of which 5104 recycled
    Never used RAM 101840, free system stack 115 words
    Tasks: SBC(ready,0.8%,418) HEAT(notifyWait,0.0%,321) Move(notifyWait,0.0%,236) CanReceiv(notifyWait,0.0%,773) CanSender(notifyWait,0.0%,335) CanClock(delaying,0.0%,340) TMC(notifyWait,7.9%,56) MAIN(running,90.8%,135) IDLE(ready,0.4%,30), total 100.0%
    Owned mutexes: HTTP(MAIN)
    === Platform ===
    Last reset 00:11:13 ago, cause: software
    Last software reset at 2023-03-18 12:26, reason: User, Gcodes spinning, available RAM 101816, slot 1
    Software reset code 0x6003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task SBC Freestk 0 n/a
    Error status: 0x00
    Aux0 errors 0,0,0
    Step timer max interval 134
    MCU temperature: min 38.7, current 39.0, max 39.6
    Supply voltage: min 23.8, current 23.9, max 24.0, under voltage events: 0, over voltage events: 0, power good: yes
    12V rail voltage: min 12.1, current 12.1, max 12.2, under voltage events: 0
    Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
    Events: 0 queued, 0 completed
    Driver 0: standstill, SG min n/a, mspos 8, reads 7952, writes 11 timeouts 0
    Driver 1: standstill, SG min 0, mspos 56, reads 7943, writes 20 timeouts 0
    Driver 2: standstill, SG min 0, mspos 904, reads 7943, writes 20 timeouts 0
    Driver 3: standstill, SG min 0, mspos 328, reads 7943, writes 20 timeouts 0
    Driver 4: standstill, SG min 0, mspos 856, reads 7943, writes 20 timeouts 0
    Driver 5: standstill, SG min 0, mspos 728, reads 7943, writes 20 timeouts 0
    Date/time: 2023-03-18 12:37:37
    Slowest loop: 62.69ms; fastest: 0.05ms
    === Storage ===
    Free file entries: 20
    SD card 0 not detected, interface speed: 37.5MBytes/sec
    SD card longest read time 0.0ms, write time 0.0ms, max retries 0
    === Move ===
    DMs created 125, segments created 3, maxWait 157284ms, bed compensation in use: mesh, comp offset 0.000
    no step interrupt scheduled
    === DDARing 0 ===
    Scheduled moves 19, completed 19, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 2], CDDA state -1
    === DDARing 1 ===
    Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
    === Heat ===
    Bed heaters 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
    Heater 1 is on, I-accum = 0.0
    === GCodes ===
    Movement locks held by null, null
    HTTP* is doing "M122" in state(s) 0
    Telnet is idle in state(s) 0
    File is idle in state(s) 0
    USB is idle in state(s) 0
    Aux is idle in state(s) 0
    Trigger* is idle in state(s) 0
    Queue is idle in state(s) 0
    LCD is idle in state(s) 0
    SBC is idle in state(s) 0
    Daemon is idle in state(s) 0
    Aux2 is idle in state(s) 0
    Autopause is idle in state(s) 0
    File2 is idle in state(s) 0
    Queue2 is idle in state(s) 0
    Q0 segments left 0, axes/extruders owned 0x80000007
    Code queue 0 is empty
    Q1 segments left 0, axes/extruders owned 0x0000000
    Code queue 1 is empty
    === CAN ===
    Messages queued 6062, received 13423, lost 0, boc 0
    Longest wait 5ms for reply type 6024, peak Tx sync delay 269, free buffers 50 (min 49), ts 3367/3366/0
    Tx timeouts 0,0,0,0,0,0
    === SBC interface ===
    Transfer state: 5, failed transfers: 0, checksum errors: 0
    RX/TX seq numbers: 26815/26815
    SPI underruns 0, overruns 0
    State: 5, disconnects: 0, timeouts: 0 total, 0 by SBC, IAP RAM available 0x26934
    Buffer RX/TX: 0/0-0, open files: 0
    === Duet Control Server ===
    Duet Control Server version 3.5.0-beta.2 (2023-02-08 11:47:09)
    Code buffer space: 4096
    Configured SPI speed: 8000000Hz, TfrRdy pin glitches: 0
    Full transfers per second: 39.99, max time between full transfers: 173.7ms, max pin wait times: 40.3ms/19.4ms
    Codes per second: 0.41
    Maximum length of RX/TX data transfers: 4480/804
    3/18/2023, 12:37:34 PM M122 B121
    Diagnostics for board 121:
    Duet TOOL1LC rev 1.1 or later firmware version 3.5beta2 (2023-02-06 18:43:58)
    Bootloader ID: SAMC21 bootloader version 2.3 (2021-01-26b1)
    All averaging filters OK
    Never used RAM 3972, free system stack 89 words
    Tasks: Move(notifyWait,0.0%,157) HEAT(notifyWait,0.5%,87) CanAsync(notifyWait,0.0%,57) CanRecv(notifyWait,0.0%,76) CanClock(notifyWait,0.0%,65) ACCEL(notifyWait,0.0%,61) TMC(notifyWait,3.1%,57) MAIN(running,91.5%,351) IDLE(ready,0.0%,26) AIN(delaying,4.9%,142), total 100.0%
    Last reset 00:11:08 ago, cause: software
    Last software reset data not available
    Driver 0: pos 0, 3200.0 steps/mm,standstill, SG min 2, read errors 0, write errors 1, ifcnt 58, reads 6615, writes 14, timeouts 0, DMA errors 0, CC errors 0, steps req 0 done 0
    Moves scheduled 0, completed 0, in progress 0, hiccups 0, step errors 0, maxPrep 0, maxOverdue 0, maxInc 0, mcErrs 0, gcmErrs 0
    Peak sync jitter -46/10, peak Rx sync delay 213, resyncs 0/0, no step interrupt scheduled
    VIN voltage: min 24.1, current 24.2, max 24.3
    MCU temperature: min 47.4C, current 48.2C, max 48.7C
    Last sensors broadcast 0x00000002 found 1 160 ticks ago, 0 ordering errs, loop time 1
    CAN messages queued 13317, send timeouts 0, received 6018, lost 0, free buffers 37, min 37, error reg 0
    dup 0, oos 0/0/0/0, bm 0, wbm 0, rxMotionDelay 0
    Accelerometer: LIS3DH, status: 00
    I2C bus errors 0, naks 3, other errors 0

    posted in Firmware installation
    undefined
    ObiJohn
    18 Mar 2023, 17:39
  • DWC 3.4.0-b3 m122 command not producing output.

    I have Board: Duet 2 WiFi (2WiFi)
    Firmware: RepRapFirmware for Duet 2 WiFi/Ethernet 3.4.0beta3 (2021-08-24)
    Duet WiFi Server Version: 1.26

    M122 diagnostics has no outputnot sure if this is a dwc issue or a firmware issue. Any help would be appreciated

    posted in Duet Web Control
    undefined
    ObiJohn
    14 Sept 2021, 02:06
  • RE: current settings for maestro

    @dc42 I was wondering is it possible to get finer adjustments in current. Part of the issue with a 4 into 1 nozzle is the 4 motors need to be balanced. If the balance is not correct you get unpredictable extrusion. The better the control over the current the more accurate the extrusion balance

    posted in Tuning and tweaking
    undefined
    ObiJohn
    31 Jul 2020, 03:49
Unless otherwise noted, all forum content is licensed under CC-BY-SA