Posts made by RincewindBoi

Thanks all! Ill try it out.

I'm working on an MPCNC and was have 2 drivers assigned to the same axis that I want to home independently to square up the axis. I can't seem to find what GCode I should be calling to do so and was wondering how I should proceed. Any tips would be very much appreciated! Thank you.

It's genuine from Printed Solid and only a month old.
Thank you

Here's what my output looks like after another test. Still no movement.

I also cam confirm that the driver got very hot during this test.

9:38:37 AMError: short-to-ground reported by driver(s) 2
Warning: high temperature reported by driver(s) 2
9:38:33 AMError: short-to-ground reported by driver(s) 2
Warning: high temperature reported by driver(s) 2
9:38:28 AMError: short-to-ground reported by driver(s) 2
Warning: high temperature reported by driver(s) 2
9:38:24 AMError: short-to-ground reported by driver(s) 2
Warning: high temperature reported by driver(s) 2
9:38:19 AMError: short-to-ground reported by driver(s) 2
Warning: high temperature reported by driver(s) 2
9:38:15 AMError: short-to-ground reported by driver(s) 2
Warning: high temperature reported by driver(s) 2
9:38:13 AMM122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.03 running on Duet Ethernet 1.02 or later
Board ID: 08DLM-996RU-N8PS4-7JKD6-3S06R-TABHP
Used output buffers: 1 of 24 (16 max)
=== RTOS ===
Static ram: 25680
Dynamic ram: 93220 of which 0 recycled
Exception stack ram used: 348
Never used ram: 11824
Tasks: NETWORK(ready,648) HEAT(blocked,1188) MAIN(running,3744) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 00:03:44 ago, cause: power up
Last software reset at 2020-08-15 18:48, reason: User, spinning module GCodes, available RAM 11824 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 27.1, current 27.6, max 27.6
Supply voltage: min 24.2, current 24.2, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: temperature-warning short-to-ground standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2020-08-19 09:38:13
Cache data hit count 571417917
Slowest loop: 1.11ms; fastest: 0.08ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 6, completed moves: 6, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = -1 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 4.02ms; fastest: 0.03ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
Interface state 5, link 100Mbps full duplex
9:38:10 AMError: short-to-ground reported by driver(s) 2
Warning: high temperature reported by driver(s) 2
9:38:06 AMError: short-to-ground reported by driver(s) 2
Warning: high temperature reported by driver(s) 2
9:38:01 AMError: short-to-ground reported by driver(s) 2
Warning: high temperature reported by driver(s) 2

Wires and steppers have been cleared as good but I'll test again tonight for my own sanity.

I'll post the M122 output when I can get to the printer.

Hello,

I picked up a Duet 2 Ethernet for my build and it was working fine for the first few minutes of running the steppers.

When testing my z-axis I started to get Short to Ground on driver 2 errors after it running fine for a while. I checked my wiring and tried different known good cables but still the same error. I also tried the driver on different steppers (also known good) and still got the same error. Both the wires and the steppers work on the other drivers.

The board was also kept in a printed box and I made sure there was no way there could have been a short caused by a rouge screw or something.

Any help would be MUCH appreciated.
Thank you!