Thanks everyone. Turns out it was my faulty crimping. I cut off all the wires on the 8-pin Molex and crimped them again. Admittedly these were my first crimps in this project and weren’t my best. LED flashes after power up and successfully ran auto-calibration.
Just have to fix the crimps on that power connector and I’ll be testing the hot end and extruder.
Thanks everyone. Turns out it was my faulty crimping. I cut off all the wires on the 8-pin Molex and crimped them again. Admittedly these were my first crimps in this project and weren’t my best. LED flashes after power up and successfully ran auto-calibration.
Just have to fix the crimps on that power connector and I’ll be testing the hot end and extruder.
Thanks for reading and assisting.
Here's the information requested.
M115
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 2.05.1 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2020-02-09b1
; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Mon Mar 30 2020 22:28:21 GMT-0500 (CDT)
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Pythagoras" ; set printer name
M665 R172 L304.11 B110 H315 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0 ; put your endstop adjustments here, or let auto calibration find them
; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X256 Y256 Z256 I0 ; configure microstepping without interpolation
M350 E16 I1 ; configure microstepping with interpolation
M92 X3200.00 Y3200.00 Z3200.00 E2700.00 ; set steps per mm
M566 X1200.00 Y1200.00 Z1200.00 E1200.00 ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z18000.00 E1200.00 ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z1000.00 E1000.00 ; set accelerations (mm/s^2)
M906 X1000 Y1000 Z1000 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 Z0 S1 ; set minimum Z
; Endstops
M574 X2 Y2 Z2 S1 ; set active high endstops
; Z-Probe
M558 P5 R0.4 H5 F1200 T6000 ; set Z probe type to effector and the dive height + speeds
G31 P100 X0 Y0 Z0.1 ; set Z probe trigger value, offset and trigger height
M557 R85 S20 ; define mesh grid
; Heaters
M305 P0 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 1
M143 H1 S280 ; set temperature limit for heater 1 to 280C
; Fans
M106 P0 S0 I0 F500 H-1 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
; Tools
M563 P0 S"Effector" D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
; Custom settings are not defined
Please disregard the wiring of the power connectors in the background of the effector picture, I know I have to fix this.
And as I stated before, I can read 3.24V between pins 6 and 8 off the wired pins on the 8-pin molex.
I am building my delta printer with a Duet WiFi and Smart Effector v1.3. When it powers on I do not see any flashing on the LED. I have checked the voltage at the wiring on the effector, and there is 3.24V between pin 6 and 8. Duet web control shows Z-Probe at 1000. G32 and G30 say Z-Probe already trigged at start of probing. I do not have the part cooling or hot end fan running, neither the heated bed.
Any recommendations or other information I should provide?
Thanks.