I now found the time to test it and by now it seems to be working. Startet 4 -5 times and it always started at X41 as you said it should. and didnt go back to -30 like before.

Thanks for your help.

I tried to install 1.19RC6 and as far as i can see it has worked M115 reports 1.19RC6. At the moment i have no way to connect it via USB as my laptop is not with me by now but with PanelDue the M122 puts something like === Diagnostics === 1 of 32 Buffers used (11 max) ….... and seems to be cut off so i dont know if Wifi update worked but it connects to my Wifi network and i can connect to it.

But i dont get the Web Control. All i get is a 404 Page. ERROR! ERROR! ERROR! The Requested file could not be found.

I did the update like described on this site https://duet3d.com/wiki/DuetWiFiFirmware_1.19beta

EDIT: I installed RC6 after testing what you suggested but didnt work so i thought ill give it a try.

EDIT2: Ok i found out what was the Problem and that it was my understanding of "Extract the content from the DWC.zip". I extracted everything even the *.gz cause i thought that whats meant. I now re-extracted the zip only and now the WebControl works. Firmwareupdate was successfull according to Settings -> General.

I will test the rest tomorrow when i got time.

Thanks for the answer.

I will try that when im home again tomorrow. The m558 command in my config.g I posted is x0 y0 z1 but I will double check that before updating to the rc6.

Hi

i recently got my DuetWifi and i installed everything with the help from this Forum and the E3D Forum so i am able to move all the Axis and Probe the bed and everything else.

Now i have 2 Problems i cant solve by my own. I tried to search that but didnt find anything, maybe the search terms i used were wrong, so sorry if that was talked about in another thread.

First is Setting an offset for the Z-Probe. I tried a few setups other BigBox users are using and it wont work.

When i Home my axis everything works but when i go back to X0 Y0 the Z-Probe is at that Point and not the Nozzle of T0.

I looked at the config.g and applied offsets (these are not apllied at the same time, its just to show what i tried)

[[language]]
M558 P1[b] X26 [/b]Y5 Z1 H5 F200 T6000 ; Set Z probe type to unmodulated, the axes for which it is used and the probe + travel speeds

G31 P500 [b]X-26[/b] Y2 Z2.0 ; Set Z probe trigger value, offset and trigger height

X-26 is what i measured with my eyes and a ruler so its not that far off of the original X-25.19 that other BigBox users have and can put than in later when i know how it works.

Inside the override_config.g is a line

[[language]]
; Z probe parameters
G31 T1 P500 X100.0 Y50.0 Z2.00

that doesnt change anything, active or commented out.

Solution to that is that my axis minima were wrong and i thought the offset would be applied after homing, but it doesn`t. I dont know when it is applied but by now it seems it is when bedlevelling is used.

My second Problem ist that when i click on "Run Mesh Grid Compensation" the Tool probes at X35 Y0 first and then goes to X-30 and tries to probe, but than the Z-Probe is not on the Bed so it will jam the nozzle in to the bed. I think that there is a fundamental Problem in my config but im absolutely new to RepRapFirmware and this board.

I will post my Config.g. If you need more i will provide it if i can. I hope you can help me with that.

[[language]]
; Configuration file for Duet WiFi (firmware version 1.17)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Tue Aug 08 2017 20:08:17 GMT+0200 (Mitteleuropäische Sommerzeit)

; General preferences
M111 S0 ; Debugging off
G21 ; Work in millimetres
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
M555 P2 ; Set firmware compatibility to look like Marlin
M208 X-45 Y0 Z0 S1 ; Set axis minima
M208 X280 Y240 Z295 S0 ; Set axis maxima

; Endstops
M574 Z0 S0 ; Define active low and unused microswitches
M574 X1 Y1 S1 ; Define active high microswitches
M558 P1 X0 Y0 Z1 H5 F200 T6000 ; Set Z probe type to unmodulated, the axes for which it is used and the probe + travel speeds
G31 P500 X-26 Y2 Z2.0 ; Set Z probe trigger value, offset and trigger height
M557 X15:205 Y15:185 S20 ; Define mesh grid

; Drives
M569 P0 S0 ; Drive 0 goes backwards
M569 P1 S0 ; Drive 1 goes backwards
M569 P2 S0 ; Drive 2 goes forwards
M569 P3 S1 ; Drive 3 goes forwards
M569 P4 S1 ; Drive 4 goes forwards
M350 X16 Y16 Z16 E16:16 I1 ; Configure microstepping with interpolation
M92 X160 Y360 Z1600 E420:420 ; Set steps per mm
M566 X900 Y900 Z12 E120:120 ; Set maximum instantaneous speed changes (mm/min)
M203 X15000 Y15000 Z150 E3600:3600 ; Set maximum speeds (mm/min)
M566 X600 Y600 Z30 E20 ; Minimum speeds mm/minute
M201 X800 Y800 Z100 E1000:1000 ; Set accelerations (mm/s^2)
M906 X800 Y700 Z800 E1000:1000 I60 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Heaters
M143 S260 ; Set maximum heater temperature to 260C
M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M305 P1 T100000 B4138 C0 R4700 X200 ; Set thermistor + ADC parameters for heater 1 and remap it to channel 200
M305 P2 T100000 B4138 C0 R4700 X201 ; Set thermistor + ADC parameters for heater 2 and remap it to channel 201
M106 F10 ; Fix for Bigbox Blower

; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
M563 P1 D1 H2 ; Define tool 1
G10 P1 X38.3 Y0.0 Z0.0 S0 R0 ; Set tool 1 axis offsets
G10 P1 R0 S0 ; Set initial tool 1 active and standby temperatures to 0C

; Network
M550 PBigBox ; Set machine name
M552 S1 ; Enable network
; Access point is configured manually via M587 by the user
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet

; Fans
M106 P0 S0 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H2 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 F10

; Custom settings are not configured
;T0  ; select first hot end (All my scripts uses T0 as reference so I always try to remember to set it so no script makes a off bed setting)