Posts made by Velixa

Ok so I lowered motor current to 0.7A, lowered acceleration to 5000 and increased instantaneous speed change to 1000. Then printed at 20°C lower both hotend and hotbed, to drain less current at print time. A 5 hours print went through without any issue.
I don't know what parameter did the magic but maybe it was reducing the overall drawed current. Maybe driver 4 draws less current so even with same config it went just borderline.
Thanks both for your tips!

I was just going to replace power supply before this whole virus lockdown. I'll look into it as soon as possibile.

Accelerations and instantaneous speed change were settings that I got from the Anet A8 defaults with reprapconfgurator.

I'll try adjusting values you both said and report back, but I somewhat feel this isn't it because when I plugged same motor same config to driver 4 (changing only the mapping), i worked flawlessly for days. I'll report as soon as I have another short-to-ground or success

I searched everywhere but couldn't find anything like my problem. I have this short-to-ground on driver 3 (extruder) that happens at random times, maybe it is after 10 minutes of starting printing without problems (extruding and all), maybe it happens after 3 hours of straight printing without problem.
When motor is not connected it won't give any error. When moving using the Duet Web Control won't give any error. I even tried extruding (without filament inserted) 10000mm at 5000 feedrate, both directions and it went fine. I tried swapping the extruder to driver 4 and it printed 10h straight and didn't give any problem in two weeks of testing. Driver itself looks fine, no hole. What the hell could it be?

Diagnostic at idle with driver 3 connected
M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.0 running on Duet WiFi 1.02 or later
Board ID: 08DDM-9FAM2-LW4T8-6J9D0-3SN6L-92XHY
Used output buffers: 3 of 24 (21 max)
=== RTOS ===
Static ram: 30516
Dynamic ram: 91880 of which 0 recycled
Exception stack ram used: 256
Never used ram: 8420
Tasks: NETWORK(ready,688) HEAT(blocked,1240) MAIN(running,3676) IDLE(ready,156)
Owned mutexes:
=== Platform ===
Last reset 00:00:13 ago, cause: power up
Last software reset at 2020-03-18 17:48, reason: User, spinning module GCodes, available RAM 8276 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 33.6, current 36.3, max 36.8
Supply voltage: min 12.1, current 12.1, max 12.3, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2020-03-18 18:07:07
Cache data hit count 24063528
Slowest loop: 2.12ms; fastest: 0.09ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 21.96ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 1 of 8

• WiFi -
  Network state is running
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.23
  WiFi MAC address 5c:cf:7f:41:30:a5
  WiFi Vcc 3.44, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 23208
  WiFi IP address 192.168.109.121
  WiFi signal strength -76dBm, reconnections 0, sleep mode modem
  Socket states: 0 0 0 0 0 0 0 0

Diagnostic after 10 minutes of printing fine and then short-to-ground error
M122
Error: short-to-ground reported by driver(s) 3
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.0 running on Duet WiFi 1.02 or later
Board ID: 08DDM-9FAM2-LW4T8-6J9D0-3SN6L-92XHY
Used output buffers: 3 of 24 (20 max)
=== RTOS ===
Static ram: 30516
Dynamic ram: 92004 of which 0 recycled
Exception stack ram used: 512
Never used ram: 8040
Tasks: NETWORK(ready,592) HEAT(blocked,1240) MAIN(running,3668) IDLE(ready,156)
Owned mutexes:
=== Platform ===
Last reset 00:14:45 ago, cause: power up
Last software reset at 2020-03-18 17:48, reason: User, spinning module GCodes, available RAM 8276 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 10
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 227.8ms, max retries 0
MCU temperature: min 34.8, current 36.9, max 37.2
Supply voltage: min 11.1, current 11.3, max 12.4, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max 0/336
Driver 1: standstill, SG min/max 0/492
Driver 2: standstill, SG min/max not available
Driver 3: short-to-ground standstill, SG min/max 0/497
Driver 4: standstill, SG min/max not available
Date/time: 2020-03-18 18:06:11
Cache data hit count 2294753149
Slowest loop: 492.27ms; fastest: 0.09ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 125, MaxWait: 172019ms
Bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 17, completed moves: 17, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.3
Heater 1 is on, I-accum = 0.4
=== GCodes ===
Segments left: 0
Stack records: 3 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 160.22ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 1 of 8

• WiFi -
  Network state is running
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.23
  WiFi MAC address 5c:cf:7f:41:30:a5
  WiFi Vcc 3.44, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 24280
  WiFi IP address 192.168.109.121
  WiFi signal strength -73dBm, reconnections 0, sleep mode modem
  Socket states: 0 0 0 0 0 0 0 0

config
config.g