@dc42 Yes, you are right. Which was done by mistake. However, the extruder never reacted even without the changes. Now I changed it back to the initial value but still nothing.
Edit: I tried switching the Drivers to the X from 0.0 to 0.3 and E from 0.3 to 0.0. Now from, I am unable to move the X motor, but the extruder works fine. Upon further inspection I realized I can't move any Stepper which is connected to the drivers 3, 4 or 5.
Also, even though the motors do not move, I do not get any errors and the tool Position and Printer Status changes. Like i mentioned before all motors and their connections are intact because they all run with the drivers 0, 1 and 2
The M122 command tells me: the driver status is okay though.
M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.4.6 (2023-07-21 14:11:38) running on Duet 3 MB6HC v1.02 or later (standalone mode)
Board ID: 08DJM-956BA-NA3TJ-6JKDL-3S06P-9T8LS
Used output buffers: 3 of 40 (13 max)
=== RTOS ===
Static ram: 153252
Dynamic ram: 98440 of which 0 recycled
Never used RAM 98980, free system stack 208 words
Tasks: NETWORK(ready,37.8%,155) ETHERNET(notifyWait,0.1%,320) HEAT(notifyWait,0.0%,321) Move(notifyWait,0.0%,352) CanReceiv(notifyWait,0.0%,943) CanSender(notifyWait,0.0%,335) CanClock(delaying,0.0%,343) TMC(notifyWait,7.6%,90) MAIN(running,54.3%,1101) IDLE(ready,0.2%,30), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:01:08 ago, cause: software
Last software reset at 2023-11-20 16:46, reason: User, GCodes spinning, available RAM 98908, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0044a000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Step timer max interval 789
MCU temperature: min 27.3, current 28.7, max 28.9
Supply voltage: min 23.9, current 24.0, max 24.0, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.1, max 12.3, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: ok, SG min 0, mspos 0, reads 56236, writes 14 timeouts 0
Driver 1: ok, SG min 0, mspos 0, reads 56236, writes 14 timeouts 0
Driver 2: ok, SG min 0, mspos 0, reads 56236, writes 14 timeouts 0
Driver 3: ok, SG min 0, mspos 0, reads 56236, writes 14 timeouts 0
Driver 4: ok, SG min 0, mspos 9, reads 56240, writes 11 timeouts 0
Driver 5: ok, SG min 0, mspos 9, reads 56240, writes 11 timeouts 0
Date/time: 2023-11-20 16:47:53
Slowest loop: 3.17ms; fastest: 0.05ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 2.3ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, segments created 0, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 1 is on, I-accum = 0.0
Heater 2 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== CAN ===
Messages queued 618, received 0, lost 0, boc 0
Longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 50 (min 50), ts 344/0/0
Tx timeouts 0,0,343,0,0,273 last cancelled message type 4514 dest 127
=== Network ===
Slowest loop: 2.78ms; fastest: 0.03ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
= Ethernet =
State: active
Error counts: 0 0 0 0 0 0
Socket states: 5 2 2 2 2 0 0 0
= WiFi =
Interface state: disabled
Module is disabled
Failed messages: pending 0, notready 0, noresp 0
Socket states: 0 0 0 0 0 0 0 0
=== Multicast handler ===
Responder is inactive, messages received 0, responses 0
