Topics created by wkellyo

@wkellyo how it's look your config.g for this application with arduino?

I doubted that you'd typed those all by hand. Well done.

@empi00 said in BLV MGN Cube Neopixel Question:

@Nuramori I tried right now the same.
But as soon as I plug the RX port in on the Arduino (directly from the PanelDue RX) the PanelDue loses the connection.
Arduino is supplied with 5V.
Did you the same?

Most Arduinos drive the RxD line from the USB converter chip via a 1K resistor, and some also connect an LED and series resistor to that line. That might be enough to override the signal. In the CNC pendant I avoided this by using the Arduino Pro Micro, which is electrically similar to the Arduino Leonardo.

Neopixels have tricky timing requirements, which means that unless you use DMA to SPI, you have to stop all other processing while writing to them.

The Duet 3 main board supports Neopixel strips directly, because the CPU on that board had a spare SPI channels that we could dedicate to Neopixel support, and enough RAM that we were able to dedicate some to a Neopixel DMA buffer. Duet 2 doesn't have a spare SPI channel.

What i've done until tody.

-The printer itselve is Grounded, Motors, Frame, Heatbed, etc.

Grounded the Heatbed Plate once more with good grounding
-Heatbed is Powerd by 230v. 1 SSR Relay.
-Now i have 2 SSR for both Phases a complete cutoff a new (https://de.aliexpress.com/item/32819816264.html?spm=a2g0s.9042311.0.0.27424c4dE5rUIG) Thermresistor
and at the end of the Heatbed a shielded cable to the Controller Duet2 Wifi Make PID tuning of the Sensor at 90°C. Kalibrate it for my surface and its perfect.
hold his temp. at 60° manually.

What i figured out:

in a test print the Thermresistor is constant at 60°C at the first layer,
then the controller board stop the impulses to the ssr, what is right, because the thermresistor getting hotter,
but the bed get colder. in the speed the bed gets colder, the thermresistor rises up.
it looks like the Thermresistor gets a switch in measure direction at the end of layer one.
Please help, i am at the end of all.
It is a config Problem?
or a hardware problem of the duet?
all the same on Firmware 2.04, 2.05, 3.0 all the same on 3.0 i made a new config.

my config of 2.04-2.05:

; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.4 on Fri Dec 13 2019 17:23:05 GMT+0100 (Mitteleuropäische Normalzeit)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"RLM" ; set printer name
M665 R157.0741 L397.19 B156 H523.32 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0 ; put your endstop adjustments here, or let auto calibration find them

; Network
M551 P"xxxxxx" ; set password
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S1 ; enable FTP
M586 P2 S1 ; enable Telnet

; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S0 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z80.00 E414.1165 ; set steps per mm
M566 X1200.00 Y1200.00 Z1200.00 E1200.00 ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z18000.00 E1200.00 ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z1000.00 E1000.00 ; set accelerations (mm/s^2)
M906 X1200 Y1200 Z1200 E630 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S9 ; Set idle timeout

; Axis Limits
M208 Z0 S1 ; set minimum Z

; Endstops
M574 X2 Y2 Z2 S1 ; set active high endstops

; Z-Probe
M307 H3 A-1 C-1 D-1 ; disable heater on PWM channel for BLTouch
M558 P9 H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X0 Y20 Z1.42 ; set Z probe trigger value, offset and trigger height
M557 R120 S30 ; define mesh grid

; Heaters
M305 P0 T100000 B4170 R4700 ; set thermistor + ADC parameters for heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M305 P1 T100000 B3950 R4700 ; set thermistor + ADC parameters for heater 1
M143 H1 S280 ; set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0 I0 F500 H-1 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T50 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S0 I0 F500 H-1 ; set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned off

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

;M501: Read stored parameters
M501 ;M501: Read stored parameters

Picture vom the ground and SSR
SSR.jpg ground.jpg

You guys Rock! I guess I had too many late nights and missed such a simple change. I now realize the Y endstop is indeed at the rear left of the machine as looked at from above, but... It's Positive and that's what I missed in the endstop configuration as you all have pointed out. I changed the Y1 to Y2 and lo and behold.. It works! Thanks to each of you for taking the time to dig through my config.g file and finding this!! Bless you all and merry christmas!!!

Kelly