Duet WiFi web interface only half working

Danal

Also, when you upload new firmware via the web interface, it both uploads the files to the /sys directory and installs them into the flash memory on the board and/or wifi module by issuing separate M commands.

If you've had trouble getting this to work, it is at least possible that your alternative methods (physical copy to the SD, etc, etc. ) got the files to /sys, but never loaded them to the board(s).

As such, repeat the uploads via the web interface, or if that is too broken, look up the G-Code to actually install the firmware. Be sure the files on the SD /sys are correct, and issue those commands.

niik

Thanks for the recommendation. I got momentary success but lost it again.

I had previously cleared the cache but it didn't fix the issue, but I had not restarted my networking equipment. I had also previously removed and re-added the pairing in the access points web interface but that did not resolve the problem.

Restarting the access point, router, and switch and also clearing cache fixed the problem. I'm not 100% sure what action resolved the issue this time since I did them all at the same time.

I was able to connect to the page for a minute but then got another error "request timed out."

List of actions.

clear cache in Edge.
restart network equipment
restart duet
connect to the webpage using edge
everything working, uploaded gcode. FIXED!!
try connecting using firefox (my main browser)
page half loads (Img 1) in firefox, at the same time I get "request timed out" in Edge window (Img 2) BROKE!!
close both browsers
restart duet
try connecting with Edge "page cant be reached"
repeat steps 1-4
"page cant be reached"

Throughout all of this, I am watching ping and am getting responses when I should.

We were so close.

Img 1 ↓

Img 2 ↓

niik

@Danal said in Duet WiFi web interface only half working:

Also, when you upload new firmware via the web interface, it both uploads the files to the /sys directory and installs them into the flash memory on the board and/or wifi module by issuing separate M commands.

If you've had trouble getting this to work, it is at least possible that your alternative methods (physical copy to the SD, etc, etc. ) got the files to /sys, but never loaded them to the board(s).

As such, repeat the uploads via the web interface, or if that is too broken, look up the G-Code to actually install the firmware. Be sure the files on the SD /sys are correct, and issue those commands.

Thanks for the advice. I followed the guides and due to my own mistakes had to go as far as flashing a fresh firmware using USB and BOSSA since I accidentally delete everything. I am getting USB connection now and the board is reporting 2.04RC1, and webServer 1.23 with webControl 1.22.6 which is the firmware I was trying to install, so it seems like the process worked. However, the firmware upgrade mostly seems to have made the issue worse since originally I could connect fine just not upload but now I can't even connect.

Danal

@niik said in Duet WiFi web interface only half working:

Throughout all of this, I am watching ping and am getting responses when I should.

This is absolutely key. Given that you can ping, the network is functioning correctly.

So... even though we think it is all good... re-flash the Duet. Specifically:

Be sure the sys/Duet2CombinedFirmware and sys/DuetWiFiServer.bin files on the SD are the versions that you want. A fresh download won't hurt.
Issue M997 S0:1 and wait for it to complete!!
Power Cycle the Duet

niik

After more troubleshooting, I have no idea...

I tried updating the firmware using fallback procedure #1 (as @Danal recommended) and ran into some more issues, details below. I have also included another m122 result since I am now seeing errors in the console maybe the m122 will have more relevant info.

Actions:

downloaded firmware
Duet2CombinedFirmware.bin (from 2.04RC1)
DuetWiFiServer.bin (from 2.03)
iap4e.bin (from 2.03)
loaded to SD card
connected to board over USB using repetier
sent M997 S0:1
waited for completion (console counted to 100% then I listened for the USB device to disappear and reappear)
5)restarted
pressed connect on Repetier → "Com port does not exist"
try the other ports. still not working.
check device manager → "Bossa port" showing instead of Duet
decide to try another firmware version
download Duet2CombinedFirmware.bin, DuetWiFiServer.bin, DuetWebControl.zip, iap4e.bin from version 1.21 and load them to the SD card
loaded firmware using "BOSSA" app following fallback procedure #3
connect to Duet over USB issue M997 S1 to load the WiFi server that matches the main.
restart
try to connect to webConsole → half loads. (img 3) and console reports Error: Can't open 0:/www/img/diabase_calibration_diagram.png.gz to read, error code 1
I get multiple of those errors depending on what is trying to load.
remove SD And check that the files are on it. They are.
delete and recreate the www folder and extract the WebControle files to it again
put SD card back and try again. same issue

Another observation is that after I try to connect to the webpage sometimes the Duet disconnects from USB and I drop like 2-3 pings, so it seems like it is getting reset.

Full console log when trying to access the web page. ↓

New conn on socket 0 for local port 80
HTTP connection accepted
Found responder
Received 391 bytes
Sending reply, file = yes
HTTP req, command words { GET / HTTP/1.1 }, parameters { }
New conn on socket 1 for local port 80
HTTP connection accepted
Found responder
New conn on socket 2 for local port 80
HTTP connection accepted
Found responder
Received 359 bytes
Sending reply, file = yes
HTTP req, command words { GET /css/dwc.css HTTP/1.1 }, parameters { }
Received 412 bytes
Sending reply, file = no
HTTP req, command words { GET /img/diabase_calibration_diagram.png HTTP/1.1 }, parameters { }
Error: Can't open 0:/www/img/diabase_calibration_diagram.png.gz to read, error code 5
Error: Can't open 0:/www/img/diabase_calibration_diagram.png to read, error code 5
Webserver: rejecting message with: 404 page not found
New conn on socket 3 for local port 0
HTTP connection accepted
Found responder
Received 342 bytes
Sending reply, file = yes
HTTP req, command words { GET /js/dwc.js HTTP/1.1 }, parameters { }
New conn on socket 0 for local port 80
HTTP connection accepted
Found responder
Received 355 bytes
Sending reply, file = yes
HTTP req, command words { GET /fonts/glyphicons.woff2 HTTP/1.1 }, parameters { }
New conn on socket 0 for local port 80
HTTP connection accepted
Found responder
Received 371 bytes
Sending reply, file = yes
HTTP req, command words { GET /css/bootstrap-theme.css HTTP/1.1 }, parameters { }
New conn on socket 0 for local port 80
HTTP connection accepted
Found responder
Received 414 bytes
Sending reply, file = yes
HTTP req, command words { GET /language.xml HTTP/1.1 }, parameters { }
Error: Cannot read file.
New conn on socket 0 for local port 80
HTTP connection accepted
Found responder
Received 463 bytes
Sending reply, file = no
HTTP req, command words { GET /rr_connect HTTP/1.1 }, parameters { password=reprap time=2019-9-24T0:48:37 }
New conn on socket 0 for local port 80
HTTP connection accepted
Found responder
Received 442 bytes

Img 3 ↓

serial: M122
=== Diagnostics ===
Used output buffers: 1 of 32 (3 max)
=== Platform ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 1.21 running on Duet WiFi 1.0 or 1.01
Board ID: 08DAM-999TL-MQ4SD-6J9FG-3S86R-T5AZZ
Static ram used: 16152
Dynamic ram used: 100400
ReWiFi: Conn 0: free
cycled dynamic ram: 2232
Stack ram used: 3576 current, 4488 maximum
Never used ram: 7800
Last reset 00:34:18 ago, cause: power up
Last software reset time unknown, reason: Stuck in spin loop, spinning module Platform, available RAM 11228 bytes (slot 2)
SofWiFi: Conn 1: free
tware reset code 0x4040 HFWiFi: Conn 2: free
SR 0x00000000, CFSR 0x00000000, ICSR 0x0043380f, BFAR 0xe000ed38, SP 0x20001b5c
Stack: 5754454e 00444ec3 004488dc 61000000 00000000 00000001 00448b11 20005494 00000001 20001774 10000000 00000001 20008c78 00006000 00000001 004451b5WiFi: Conn 3: free
00000001 00000000 00000001 0041be93 0000000f 03b14fWiFi: Conn 4: free
ff 00000000 0041cc01
Error status: 1
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms
MCU temperature: min 25.7, current 35.9, max 36.7
SupWiFi: Conn 5: free
ply voltage: min 0.0, current 12.3, max 12.5, under voltage events: 0, over voWiFi: Conn 6: free
ltage events: 0
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill,WiFi: Conn 7: free
SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 1970-01-01 00:00:00
Slowest main loop (seconds): 0.053961; fastest: 0.000041
=== Move ===
MaxReps: 6, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm 237, MaxWait: 18530WiFi:
43626ms, Underruns: 0, 0
Scheduled movWiFi: xmit: 0
es: 3, completed moves: 3
Bed compensation in use: mesh
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 1 alWiFi: recv: 0
located, 0 in use
Movement lock held by null
http is idle in state(s) 0
teWiFi: fw: 0
lnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "M122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autWiFi: drop: 0
opause is idle in state(s) 0
Code queue is empty.
=== Network ===
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTPWiFi: chkerr: 0
(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 0 of 8
- WiFi -
Network state is running
WiFi module is connected to access point
Failed messagesWiFi: lenerr: 0
: pending 0, notready 0, noresp 0
WiFi firmware version 1.21
WiFi MAC address 5c:cf:7f:2c:25:13
WiFi Vcc 3.39, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 16120
WiFi IP address 192.168.1.181
WiFi signal strength -47dBm, recoWiFi: memerr: 0
nnections 0, sleep mode modem
SoWiFi: rterr: 0
cket states: 0 0 0 0 0 0 0 0
=== Expansion ===
ok
WiFi: proterr: 0
WiFi: opterr: 0
WiFi: err: 0
WiFi: cachehit: 0
WiFi:
WiFi: xmit: 53
WiFi: recv: 487
WiFi: fw: 0
WiFi: drop: 179
WiFi: chkerr: 0
WiFi: lenerr: 0
WiFi: memerr: 0
WiFi: rterr: 0
WiFi: proterr: 179
WiFi: opterr: 0
WiFi: err: 0
WiFi: cachehit: 1900
WiFi:
WiFi: xmit: 1968
WiFi: recv: 5399
WiFi: fw: 0
WiFi: drop: 678
WiFi: chkerr: 0
WiFi: lenerr: 0
WiFi: memerr: 0
WiFi: rterr: 0
WiFi: proterr: 0
WiFi: opterr: 0
WiFi: err: 0
WiFi: cachehit: 0
WiFi:
WiFi: xmit: 24
WiFi: recv: 0
WiFi: drop: 0
WiFi: chkerr: 0
WiFi: lenerr: 0
WiFi: memerr: 0

Danal

@niik said in Duet WiFi web interface only half working:

restart

try to connect to webConsole → half loads. (img 3) and console reports Error: Can't open 0:/www/img/diabase_calibration_diagram.png.gz to read, error code 1
I get multiple of those errors depending on what is trying to load.

That is really odd. There is no such file in a Duet's /www directory as distributed. In fact, there is no such directory as /www/img. DWC does not use images (png).
(It does use a favicon.ico.gz file, but no other images).

I do see that the functions that are built into DWC to automatically put various files in their correct directory, by file extension, WILL build a /www/img directory and put any .png, .jpg, or .jpeg files there. So, at some point in the past, some files with those extensions got uploaded.

My advice at this point:

First, try to fix the www directory:

Put the SD in your PC and delete /www (and everything under it). Back it up first, if you wish.
Download DuetWebControl-Duet2.zip This is R2.0.0-RC7, which should work fine with the firmware you've loaded. If you want another release, see here
Unzip it into a new, empty /www on the SD. After the unzip, the directory should look like:
css (dir)
fonts (dir)
js (dir)
index.html.gz
favicon.ico.gz
... and maybe one or two other files, but NO 'img' directory!
Put that in the printer and see what you get.

If (and only if) that does not work, build a physically new SD. Be sure and start by formatting the new SD as a "FAT32", and be sure and UNcheck "quick format". Then copy stuff over. Including the newly built www directory.

Shaun

I had the exact same. so this is what i had to do to fix this.

Check your wifi security on your router. duet doesnt seem to like multi mode authentication. Set your router to WPA2-PSK and your problem should be resolved. It wont drop off and the browser will work fine.

niik

Test 1
@Danal said in Duet WiFi web interface only half working:

First, try to fix the www directory:

Put the SD in your PC and delete /www (and everything under it). Back it up first, if you wish.

Download DuetWebControl-Duet2.zip This is R2.0.0-RC7, which should work fine with the firmware you've loaded. If you want another release, see here

Unzip it into a new, empty /www on the SD. After the unzip, the directory should look like:
css (dir)
fonts (dir)
js (dir)
index.html.gz
favicon.ico.gz
... and maybe one or two other files, but NO 'img' directory!

Put that in the printer and see what you get.

Results:
Webpage loaded a 404 error and console also reported an error

New conn on socket 0 for local port 80
HTTP connection accepted
Found responder
Received 391 bytes
Sending reply, file = no
HTTP req, command words { GET / HTTP/1.1 }, parameters { }
Error: Can't open 0:/www/reprap.htm.gz to read, error code 4
Error: Can't open 0:/www/reprap.htm to read, error code 4
Error: Can't open 0:/www/html404.htm to read, error code 4
Webserver: rejecting message with: 404 page not found

This result makes me think the WebControle and webServer versions I am using are not compatible.

Also, the M122 console output looks odd

12:32:18.716 : WiFi firmware versiWiFi: lenerr: 0
12:32:18.716 : on 1.21

Test 2:
Migrate back to the 2.04RC1 and webServer 1.23 but keep using webControl 2.0.0-RC7

loaded relevant .bin files to the SD and installed using fallback procedure #1 steps

Results:

The page starts to load but gets stuck. I no longer get any errors in the console when trying to access the web console.

Verified firmware update

=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.04RC1 running on Duet WiFi 1.0 or 1.01
Board ID: 08DAM-999TL-MQ4SD-6J9FG-3S86R-T5AZZ
Used output buffers: 1 of 24 (2 max)
....
- WiFi -
Network state is running
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23

Never gets past this page.
page loading result from test 2

Test 3:
@Danal said in Duet WiFi web interface only half working:

If (and only if) that does not work, build a physically new SD. Be sure and start by formatting the new SD as a "FAT32", and be sure and UNcheck "quick format". Then copy stuff over. Including the newly built www directory.

Formated another SD card using SDformatter.exe with settings FULL(overWrite) FORMAT, SIZE ADJUSTMENT ON. The card was previously used in a Pi so I could not format it with windows until the Linux partitions were removed.

Confirmed FAT32 file system

Copied all files from SD1 to SD2.

Results: FIXED!!!

Page loaded and connected to the printer. I uploaded a file a ran a test print.

Couple small errors

M141: not chamber heater has been configured for slot 0
Failed to get file list - directory 0:/filaments not found

I think these are relatively self-explanatory errors and I can work through them.

Summery

After all the stuff I think I have an idea about how everything happened.

I had a network issue that caused my original upload problems.
1.1. Updating the firmware was probably not necessary
My first and second SD cards were bad leading to unexpected and unpredictable results.
2.1. SD1 has been in since I got the board so could have worn out.
2.2. SD2 is an almost new card that was used for pictures like once. So must have been defective or the format I ran on it when I first set it up completed with unknown errors.
SD3 was a card I had in a Pi and it seems to have fixed the issues I was having.

droftarts

SD card specification for Duet is here: https://duet3d.dozuki.com/Wiki/SD_Card
(I've just updated the bit about formatting, and size limit)
For M141 error (it's Cura) see: https://forum.duet3d.com/topic/11546/cura-4-2-1-to-duet2wifi-plugin-problem
You need to create a filaments folder on the SD card.

Ian

Danal

@niik said in Duet WiFi web interface only half working:

Results: FIXED!!!

YAY!!