Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Build and store multiple MESH profiles?

    Scheduled Pinned Locked Moved
    General Discussion
    4
    11
    430
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Rat_Patrolundefined
      Rat_Patrol
      last edited by

      Is this possible?

      I run the maximum number of data points I can, so it takes about 30 minutes or so to run the full bed probe sequence.

      I also switch between smooth and textured Prusa build sheets.

      Is there a way to build, store, then recall specific MESH profiles, where I can just call a specific profile in the slicer starting code?

      droftartsundefined zaptaundefined 2 Replies Last reply Reply Quote 0
      • droftartsundefined
        droftarts administrators @Rat_Patrol
        last edited by

        @Rat_Patrol Bed meshes are really stored as profiles, just filenames. So you can't load a 'profile', but you can load a specific heightmap. Run G29 as normal, which will save a new 'heightmap.csv'. Either rename this, or save current heightmap to a new csv file with G29 S3 P"filename". Load a specific heightmap with G29 S1 [P"filename"]. See https://duet3d.dozuki.com/Wiki/Gcode#Section_G29_Mesh_bed_probe

        Ian

        Bed-slinger - Mini5+ WiFi/1LC | RRP Fisher v1 - D2 WiFi | Polargraph - D2 WiFi | TronXY X5S - 6HC/Roto | CNC router - 6HC | Tractus3D T1250 - D2 Eth

        1 Reply Last reply Reply Quote 0
        • Rat_Patrolundefined
          Rat_Patrol
          last edited by

          Can you access and change the name through the web interface, or must you power down and pull the SD card?

          droftartsundefined 1 Reply Last reply Reply Quote 0
          • Rat_Patrolundefined
            Rat_Patrol
            last edited by

            I think I figured it out.

            1 Reply Last reply Reply Quote 0
            • droftartsundefined
              droftarts administrators @Rat_Patrol
              last edited by

              @Rat_Patrol said in Build and store multiple MESH profiles?:

              Can you access and change the name through the web interface

              Yes. You'll also want to set the Z datum after changing, with G30.

              Ian

              Bed-slinger - Mini5+ WiFi/1LC | RRP Fisher v1 - D2 WiFi | Polargraph - D2 WiFi | TronXY X5S - 6HC/Roto | CNC router - 6HC | Tractus3D T1250 - D2 Eth

              1 Reply Last reply Reply Quote 0
              • Rat_Patrolundefined
                Rat_Patrol
                last edited by

                I'm then assuming my startup code should look like:

                G28
                G29 S1 P"smooth.csv"
                G30

                rest of code

                droftartsundefined Phaedruxundefined 2 Replies Last reply Reply Quote 0
                • droftartsundefined
                  droftarts administrators @Rat_Patrol
                  last edited by

                  @Rat_Patrol Sounds sensible. Give it a go!

                  Ian

                  Bed-slinger - Mini5+ WiFi/1LC | RRP Fisher v1 - D2 WiFi | Polargraph - D2 WiFi | TronXY X5S - 6HC/Roto | CNC router - 6HC | Tractus3D T1250 - D2 Eth

                  1 Reply Last reply Reply Quote 0
                  • Phaedruxundefined
                    Phaedrux Moderator @Rat_Patrol
                    last edited by

                    @Rat_Patrol said in Build and store multiple MESH profiles?:

                    G28
                    G29 S1 P"smooth.csv"
                    G30

                    Don't forget to position the probe at bed center before sending the G30

                    Z-Bot CoreXY Build | Thingiverse Profile

                    Rat_Patrolundefined 1 Reply Last reply Reply Quote 0
                    • Rat_Patrolundefined
                      Rat_Patrol @Phaedrux
                      last edited by

                      @Phaedrux said in Build and store multiple MESH profiles?:

                      @Rat_Patrol said in Build and store multiple MESH profiles?:

                      G28
                      G29 S1 P"smooth.csv"
                      G30

                      Don't forget to position the probe at bed center before sending the G30

                      Wait, why is center of bed important?

                      1 Reply Last reply Reply Quote 0
                      • Phaedruxundefined
                        Phaedrux Moderator
                        last edited by

                        Well usually you'd probe the center of the bed when homing, and normally you place the print object at the center of the bed, and since the center of the bed is in the center of roll and pitch for the leveling screws.

                        Z-Bot CoreXY Build | Thingiverse Profile

                        1 Reply Last reply Reply Quote 0
                        • zaptaundefined
                          zapta @Rat_Patrol
                          last edited by

                          @Rat_Patrol said in Build and store multiple MESH profiles?:

                          I run the maximum number of data points I can, so it takes about 30 minutes or so to run the full bed probe sequence.

                          Another feature that may address this problem is being able to mesh before every print, just in the printed area. This will give very accurate mesh result in a very short time since most prints are much smaller than the bed area.

                          Any thoughts?

                          1 Reply Last reply Reply Quote 0
                          • First post
                            Last post
                          Unless otherwise noted, all forum content is licensed under CC-BY-SA