Error: short-to-ground on driver 0

tobias3333

Hi Ian, no problem and thanks for the quick respond.

The config file is attached and following is the M115 response.

23:11:43M115
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 2.05 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2019-12-13b1

config.json

Phaedrux

@tobias3333 said in Error: short-to-ground on driver 0:

config.json

Can you post the actual config.g from the sys directory? It's human readable and much easier to understand.

droftarts

@tobias3333 Thanks for the info. The config.json is the output from the Firmware Config tool, and tells me a lot, but doesn't show how your machine is set up now. Ideally, we need to see the config.g file. If you can access the Duet through DWC, go to 'System', select 'config.g' from the file list, and copy the text from there into your reply post.

Edit: @Phaedrux beats me to it, again!

Ian

tobias3333

Got it:

; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Wed Feb 12 2020 19:41:41 GMT+0100 (Mitteleuropäische Normalzeit)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"CoreXY" ; set printer name

M667 S1 ; select CoreXY mode

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S0 ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X200.00 Y200.00 Z400.00 E418.00 ; set steps per mm
M566 X720.00 Y720.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z250.00 E1000.00 ; set accelerations (mm/s^2)
M906 X1600 Y1600 Z1600 E1600 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X350 Y350 Z350 S0 ; set axis maxima

; Endstops
M574 Z0 S0 ; set active low and disabled endstops
M574 X1 Y1 S1 ; set active high endstops

; Z-Probe
M558 P5 R0.4 H5 F1200 T6000 ; set Z probe type to effector and the dive height + speeds
G31 P25 X28.5 Y-5 Z0 ; set Z probe trigger value, offset and trigger height
M557 X15:285 Y15:285 S20 ; define mesh grid

; Heaters
M305 P0 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 0
M143 H0 S100 ; set temperature limit for heater 0 to 100C
M305 P1 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 1
M143 H1 S260 ; set temperature limit for heater 1 to 260C

; Fans
M106 P0 S0 I0 F500 H-1 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1 T45 ; set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

droftarts

@tobias3333 Your config.g looks pretty standard, and I can't see anything obviously wrong. The X is configured the same as Y, which works. You are running in CoreXY mode, so it might be worth turning this off by commenting out the 'M667 S1 ; select CoreXY mode' with a semicolon ';' then testing the motor movement again. If X doesn't move and Y does, swap the motors and test again. Make sure you turn off power, or you can damage the stepper drivers by disconnecting/connecting motors when the driver is powered up. I think if this doesn't work, it's a damaged/failed/faulty driver chip.

Let me know to confirm the above. If it's the chip, it's probably a warranty replacement. Sorry for the inconvenience.

Ian

tobias3333

@droftarts: I just check your suggestion and I have to reply that it is still the same result. On the Y-Side the motor is turning. Switching to the X-Side there is again the fault message with the shorted driver0

droftarts

@tobias3333 okay. Is this a new Duet, or was it previously working? Where did you buy it, and when? If it’s a genuine Duet, bought from Duet3D or one of the resellers, and is within its warranty period, I’m happy to approve a warranty replacement. Contact your supplier, follow their warranty process, and refer them to this thread.

If you could post a picture of your Duet, or at least post the information from the sticker on the main processor, that would help identify the manufacturing date and supplier. Thanks!

As an aside, the only known causes of short-to-ground error reports are:

Genuine short (to ground or across the motor)
Motor phases not connected correctly
On a Maestro, running in stealthChop mode at high speeds (probably possible with Duet 3 too)
Failed driver
Bad SPI signals (especially if ALL drivers report short-to-ground)

Ian

tobias3333

@droftarts: Thanks for the clear statement. The board was bought at the Duet´s suggested German supplier Makerdise.com therefore it should be a genuine board?! I ordered it by the end of September 2019. Due to personel reasons there was no possibility for me to install the board since the last weeks.

So the board wasn´t running within the printer already. I started with the step by step guide from the Dozuki site.
When heading to the task to check the motors, the failure already appeared.

I already contacted the support from Makerdise to solve the issue but since 10 days there is no further feedback on how to go ahead / or initate a replacement.
Hopefully they will reply within the next days and give some feedback.

Anyway beside the support problems thank you very much for your time and the great support!

droftarts

@tobias3333 no problem, hopefully your warranty replacement will work better!

If you could post a picture of your Duet, that would be great.

M584 X0 Y1 Z2 E3 ; set drive mapping

As you’re only using 4 of the 5 drivers, you could remap X to the spare one, while you wait for the replacement. Add this line after the other M569 commands:

M569 P4 sS1 ; physical drive 4 goes forwards

Change M584 to:

M584 X4 Y1 Z2 E3                                   ; set drive mapping

and connect X motor to E1 stepper driver.

Ian

tobias3333

@droftarts: The driver re-mapping seems to work for the moment.

Replacement is still on-going.

Attached a picture of the board as requested