Webserver won't start

Haffwalker · 2 Apr 2020, 12:33

Is it possible, that when I erased the board, that any kind of firmware which is supposed to run on the ethernet module got deleted as well? Maybe I have to flash firmware on that thing too?

Dougal1957 · 4 Feb 2020, 12:34

@Haffwalker I note you said you formatted the SD Card you did install all the Config files as well as the DWC Files didn't you?

Can you post your Config.g file from the SD Card

Doug

Haffwalker · 2 Apr 2020, 12:37

Hi, SD looks like this:

Inside of www:

And my config.g looks like this:

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Tue Jan 28 2020 00:41:51 GMT+0100 (Central European Standard Time)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"AKLP Plus+" ; set printer name
M665 R135.4 L267 B118 H300 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0 ; put your endstop adjustments here, or let auto calibration find them

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S0 ; physical drive 0 goes forwards
M569 P1 S0 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z80.00 E418.50 ; set steps per mm
M566 X250.00 Y250.00 Z800.00 E200.00 ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z18000.00 E1200.00 ; set maximum speeds (mm/min)
M201 X2000.00 Y2000.00 Z2000.00 E1000.00 ; set accelerations (mm/s^2)
M906 X1100 Y1100 Z1100 E1000 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 Z-20 S1 ; set minimum Z

; Endstops
M574 X2 S1 P"xstop" ; configure active-high endstop for high end on X via pin xstop
M574 Y2 S1 P"ystop" ; configure active-high endstop for high end on Y via pin ystop
M574 Z2 S1 P"zstop" ; configure active-high endstop for high end on Z via pin zstop

; Z-Probe
M558 P5 C"e0stop" H5 A3 F360 T6000 ; set Z probe type to switch and the dive height + speeds
G31 P500 X0 Y0 Z16.254 ; set Z probe trigger value, offset and trigger height
M557 R110 S19 ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M143 H1 S280 ; set temperature limit for heater 1 to 280C
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit

; Fans
M950 F0 C"fan0" ; create fan 0 on pin fan0 and set its frequency
M950 F1 C"fan1" ; create fan 1 on pin fan1 and set its frequency Hotend Cooler
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M106 P1 S127 H1 T50 ; set fan 1 value. Thermostatic control is turned on Hotend Cooler ab 50°C mit 12V

; Tools
M563 P0 S"Hotend 1" D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501 ; load saved parameters from non-volatile memory

droftarts · 2 Apr 2020, 12:37

@Haffwalker Reading through the thread, it doesn't seem that this is a Duet-related problem, I think more likely is that the TL-WR802N is blocking http requests to the Duet from the network. What settings are there to configure it?

To test the Duet, if you can move it to plug the ethernet directly into your main router, using a USB power adapter to power it, you should be able to access it.

Ian

Haffwalker · 2 Apr 2020, 12:39

Hi, yes I already took the WR802N out of the equation - the Duet is currently directly plugged into my router.

Dougal1957 · 2 Apr 2020, 12:39

@droftarts I think his M552 line is wrong for an Ethernet version should it not have P0.0.0.0 to tell it to pick up an address via DHCP also not sure if you really need the S1 to enable it as well

A Former User · 2 Apr 2020, 12:40

@Haffwalker said in Webserver won't start:

Is it possible, that when I erased the board, that any kind of firmware which is supposed to run on the ethernet module got deleted as well? Maybe I have to flash firmware on that thing too?

The firmware relating to the network is part of the Duet's RepRap firmware which you have at v3.0, so no. As far as replacing the Ethernet module its a possibility, but I'd be surprised to see it make a difference.

To get to the bottom of whats going on we'd need something like a wireshark log of the traffic, which is a bit difficult to do without a bridge or managed switch with a mirror feature as far as I can tell.

I suppose you can as a last effort set up a static IP address on your computer using the same ethernet cable (and no wifi), then set up the Duet 2 Ethernet with the same address and see if it works to rule out issues with DHCP (but its such a simple, tried and true protocol that incompatibilities are rare)

A Former User · 2 Apr 2020, 12:42

@Dougal1957 said in Webserver won't start:

@droftarts I think his M552 line is wrong for an Ethernet version should it not have P0.0.0.0 to tell it to pick up an address via DHCP also not sure if you really need the S1 to enable it as well

He's supposedly tried the Duet without the SD card and thus no config, using only M552 S1

droftarts · 2 Apr 2020, 12:45

@Haffwalker said in Webserver won't start:

Hi, yes I already took the WR802N out of the equation - the Duet is currently directly plugged into my router.

Okay! Sorry, just catching up...

@Dougal1957 said in Webserver won't start:

@droftarts I think his M552 line is wrong for an Ethernet version should it not have P0.0.0.0 to tell it to pick up an address via DHCP also not sure if you really need the S1 to enable it as well

Quite right. M552 should be M552 P0.0.0.0 S1 for DHCP, or for a fixed IP address, set the address using the P parameter.

Ian

Dougal1957 · 2 Apr 2020, 12:46

@droftarts I think his config is the one from his WiFi first post says he swapped them over it's one of those little things that catch us all out from time to time!

A Former User · 4 Feb 2020, 16:19

@Dougal1957 said in Webserver won't start:

@droftarts I think his config is the one from his WiFi first post says he swapped them over it's one of those little things that catch us all out from time to time!

@droftarts said in Webserver won't start:

Quite right. M552 should be M552 P0.0.0.0 S1 for DHCP, or for a fixed IP address, set the address using the P parameter.

see my post https://forum.duet3d.com/post/142097 Duet2Ethernet, no SD card, only send M552 S1 gets IP from DHCP server no problem. M552 P0.0.0.0 S1 will also work, but isn't needed unless to override a stored/configured static IP for a ~~Wifi~~ network afaik.

Haffwalker · 4 Feb 2020, 12:52

Well about the M552 P0.0.0.0 S1...I already tried that but it didnt make any difference...even if I specify an IP address eg. 192.168.0.14, it won´t work...I double and triple checked with my router and that IP isn`t occupied by any other device.

Dougal1957 · 2 Apr 2020, 12:52

@Haffwalker what's in your Config-overide.g?

Haffwalker · 2 Apr 2020, 12:53

@Dougal1957 SD card isn't plugged in right now.

A Former User · 2 Apr 2020, 12:53

With the risk of repeating myself, its not a config issue if it doesn't work with the SD card removed.

Dougal1957 · 2 Apr 2020, 12:54

@bearer I think you'll find that the duet won't come up at all without an SD Card inserted but I am prepared to be proved wrong

A Former User · 4 Feb 2020, 12:57

@Dougal1957 said in Webserver won't start:

@bearer I think you'll find that the duet won't come up at all without an SD Card inserted but I am prepared to be proved wrong

@bearer said in Webserver won't start:

@Dougal1957 said in Webserver won't start:

@droftarts I think his config is the one from his WiFi first post says he swapped them over it's one of those little things that catch us all out from time to time!

see my post https://forum.duet3d.com/post/142097 Duet2Ethernet, no SD card, only send M552 S1 gets IP from DHCP server no problem. M552 P0.0.0.0 S1 will also work, but isn't needed unless to override a stored static IP for a Wifi network afaik.

there you go; proven wrong. (i.e. the whole session from the serial terminal is shown, M552 is send over serial to rule out other config issues)

droftarts · 2 Apr 2020, 12:56

@Haffwalker At some point you changed from 3.01-RC5, which got an IP address, to 3.0, which doesn't. At what point did you also disconnect the TL-WR802N?

Just for completeness, can you downgrade to 2.05.1, and try connecting again, without SD card?

Ian

Dougal1957 · 2 Apr 2020, 12:58

@bearer I Stand corrected I know that wouldn't work several years back.

Haffwalker · 2 Apr 2020, 12:58

@droftarts I will downgrade to 2.05.1 now, will let you know how if it works.