• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

all fans don't work

Scheduled Pinned Locked Moved
Duet Hardware and wiring
3
18
464
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    massimilianoconti
    last edited by 15 Apr 2020, 20:35

    with tester I checked continuity and everything seems ok. I attach the photo I believe tr5 broken. I don't know how it is possible. however no fan works
    fan duet 2.jpg

    1 Reply Last reply Reply Quote 0
    • undefined
      massimilianoconti
      last edited by 15 Apr 2020, 20:48

      I can't say more than that. I know that everything has gone well to date, it didn't take this problem, it forces me to replace the whole board I think. without fans no one can go.

      1 Reply Last reply Reply Quote 0
      • ?
        A Former User
        last edited by A Former User 15 Apr 2020, 20:55

        Try measuring as indicated, should beep or measure close to 0 ohm in all cases.
        2020-04-15 22_49_37-Clipboard.jpg

        1 Reply Last reply Reply Quote 0
        • undefined
          massimilianoconti
          last edited by 15 Apr 2020, 21:03

          there is continuity between the jumper and fan bridge and fuse. the size of the tr5 I did not understand how to do it

          1 Reply Last reply Reply Quote 0
          • undefined
            massimilianoconti
            last edited by 15 Apr 2020, 21:07

            I had seen badly I checked everything also the continuity between resistance and fan and power supply all ok

            ? 1 Reply Last reply 15 Apr 2020, 21:11 Reply Quote 0
            • ?
              A Former User @massimilianoconti
              last edited by A Former User 15 Apr 2020, 21:11

              @massimilianoconti said in all fans don't work:

              all ok

              if you the connect a fan to the always on ports and it doesn't work, then the fan (or power supply is broken)

              To check mosfet TR5 you can mesure from Vfan- and GND like shown (use diode test --|>|--)
              2020-04-15 23_10_53-2020-04-15 22_49_37-Clipboard_mosfet_tr5.jpg

              1 Reply Last reply Reply Quote 0
              • undefined
                massimilianoconti
                last edited by 15 Apr 2020, 21:22

                the voltage is not zero, it marks a value

                1 Reply Last reply Reply Quote 0
                • ?
                  A Former User
                  last edited by 15 Apr 2020, 21:25

                  I'm sure it won't kill you to be specific, about both measurements, need to reverse polarity and repeat measurement.

                  1 Reply Last reply Reply Quote 0
                  • undefined
                    massimilianoconti
                    last edited by 15 Apr 2020, 21:46

                    I see + 0.3 v and -0.3 v

                    1 Reply Last reply Reply Quote 0
                    • ?
                      A Former User
                      last edited by 15 Apr 2020, 22:20

                      Negative reading on a diode test, and fans that dont work when they should. I think you need an excorcist, or maybe some pictures showing measurement and meter.

                      1 Reply Last reply Reply Quote 0
                      18 out of 18
                      • First post
                        18/18
                        Last post
                      Unless otherwise noted, all forum content is licensed under CC-BY-SA